Hi ,
I am developing an application which uses nrf52833. I want to perform OTA using 4g module(from Quectel). As per my understanding and explorations, there can be two...
Hello,
I'm using two nRF9161 to communicate with each other and I want to test and measure the differences between the 3 modes available in SDK3.0.0. First, I configured...
I have tested the nRF Cloud Multi Service Sample using Quick Start and it works perfectly.
I am trying to build the sample so that I can make small modifications for an...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hello, I've recently upgraded my pre-production application on nrf52832 from NCS v2.6.2 to Ncs v3.0.1 also upgraded to HWv2(on interim ncs 2.9.0 as adding custom board for...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hi,
I am trying to install NCS v3.0.1 on Ubuntu 24.04 PC and I get the following error.
Looks like ZEPHYR_BASE is not setup. I am trying to follow the Fundamentals Course...
Hi,
I have a custom board build with an nrf9151. Right now I'd like to have the possibilty ti get modem trace. But it's look like I got crypted/corrupted data from UART1...
Hi,I am using NRF54L15 DK in which I need to transmit audio data over BLE where that data will be used for only plotting in application,I am using sampling rate of 16000 and...
Hello,
I'm currently working with the channel_sounding_ras_initiator project on the nRF54L15 DK , using the nRF Connect SDK from the latest main branch on GitHub ( nrfconnect...
Dear all,
i building the example light_switch_server_nrf52832_xxAA_S132_7.2.0 from solution l ight_switch_server_nrf52832_xxAA_S132_7.2.0 in configuration Debug (SDK nRF5...
Performance on hardware (cc3xx) is significantly slower than performance on software (oberon). Does anyone have a good explanation for this? I have also tested ECDSA and can...
Hello. I try to create a remote control for GoPro using nrf52 ble.
Using sdk 17.1 examples I can connect to GoPro and try to get a list of UUIDs. But I only get one UUID...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
Hello
I'm using the settings partition to store user configuration data. I know that the BLE stack also uses it — particularly for storing bonding information — but I don...
Dear Nordic:
I used V2.8.0 SDK to build light bulb, and I have commissioned bulb A(node id: 11) and bulb B (node id: 11) successfully!
Then I used below command to add...
Hi,
I am working on a project with nrf52832 and LIS3DH for a beacon.
I have added the low power feature into my application to go to standby mode in case of inactivity...
Hi,
I try to migrate a working nRF53 Zigbee project from SDK 2.7 to the latest SDK and an nRF54. As described here, I also switched to Zigbee R23. The project structure...
Hey there!
I'm trying to run the 'wifi/shell' sample on v3.0.1 on a nrf7002dk (targeting the nrf7002dk/nrf5340/cpuapp) with sysbuild enabled, of course and I'm getting...
