HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I load the s110 softdevice (I tried many versions 5, 6 and 7)
When I load my app on the SOC using Keil and the nrf_xxaa_s110 (256) target, the app doesn't run.
I'm...
Dear Nordic Developer Zone,
I have implemented a real-time-clock using application timer which is based on the on-chip real-time counter on NRF51822.
A concern of mine...
I'm trying to get the Nan-36 example working on my PC10001 board and I'm having some trouble. I've tried using both SD110 version 6 and 7 with appropriate (I think) memory...
Hi,
Is there any connection/disconnection API in ant+ (sd210) similar to BLE?
I want to use this to control the device activity cycle, if I get disconnection event, would...
Hi,
I'm trying to implement a specific communication protocol using the SPI on a nRF51822. The SPI on nordic side will act as slave. When CSN line goes low, I will also need...
Hi,
I currently have a problem with the continous scanning mode. I implemented the scanning mode that my device searches for the first 4 seconds after power up then picks...
Which example projects are compatible with s110 v7 for nRF51822?
I keep running into samples requiring "Legacy Keil" to be installed.
I just want a clean s110 v7 example...
Uint32_t data using sd_flash_write written many times to the same address, you must perform sd_flash_page_erase before writing it?
(English is not good, with Google Translate...
Is the DC/DC converter enabled when running ble_app_beacon?
Or is it only the LDO that is enabled?
I am running the application on nRF51822-DK.
BR Magnus
Hi,
I happily use the JLINK UART interface which show up as COMxx on windows for both the PCA10000 and PCA10001.
We are trying to 'see' the same on Linux. Have inatlled...
Could you please let me know the current rating in between retries while transmitting.From the oscilloscope reading, that is not obvious. The documentation shows three idle...
Hi
We had some problems updating our devices with the nRF Loader App on IOS. After selecting the device in DFU mode the App hangs and aborts with a Bluetooth error after...
Has anyone been able to get the DFU over the air bootloader to work with gcc and the newest SDK (6.0)?
I have followed all the tips I can find on here to get it working...
I'm wondering if the timeslot API is planned for the s130 or if it's intended to be s110 only. If it is eventually getting added to the s130 is there a loose time frame for...
Hello,
i am using the nrf51822 with softdevice s110. In the spec i read that the contoller works as well with an external 32khz reference which i want to use. The oszillator...
