I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
I want to access an SPI-only sensor device from a Blend Micro.
There is a need to avoid collisions between the two uses of the SPI port for the sensor and the nRF chip...
I just made it to upload the example to the device. I'm new into firmware development btw.
I changed the timeout so the beacon will stop advertising after 120 seconds but...
Hello, I have implemented the code below for my project
based on switching central and peripheral role in S130.
The code works fine on the Devkit PCA10028 but on porting...
In compatibility matrix it is shown that s110 v 7.3.0 is compatible with nrf51422 when using SDK 7.x.x. But when I downloaded s110 v7.3.0 in its name and specification documents...
I tried to build the example project "ble_app_uart" bundled with nRF5 SDK (nRF5_SDK_11.0.0_89a8197) within the MDK-Lite V5.18K. It failed and I got the following messages...
Hi!
I am attempting to flash sdk11 examples onto a QFAB board compiled using arm-gcc over JLINK SWD p20 via the NRF-51DK.
While running make flash, the nrfjprog command...
Hello I found example for dual bank bootloader ("examples\dfu\bootloader\pca10040\dual_bank_ble_s132"). And it works well.
Do you plan also to add a SINGLE bank boot-loader...
hi all,
I am using SDK version 8.
i want to make button as ON and off switch.
REQUIREMENT:
When button is pressed counter should keep on incrementing when i released...
Hello,
I would like to simulate the spreading of a disease using the nrf51822 beacons. My question is if my envisioned project is possible as I'm completly new to nrf51822...
I would need to change a timer into single shot mode. My code is as follows:
static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(MY_SAMPLE_TIMER);
nrf_drv_timer_init...
using S130, SDK11,
CANNOT work the two heart rate sensors which have the different deivce name ?
when it connected the heart rate sensor A and eveything is OK.
but...
Hello,
I want to use nRF52832 at 2V. But I am not sure what would be the current consumption of radio during transmission and reception with DCDC regulator on. In datasheet...
Hi, after some research and reading several posts (especially this one ), I am still confused about the Flash endurance on the nRF52.
In the product specification for the...
