Hi all
I have a project that I developed with SDK 17.0.2 in Segger Embedded Studio. It works well, but now I would like to add a GitHub Runner to compile it every time I...
Hi,
I’m trying to use the SoftDevice Controller in peripheral-only mode on the nRF54L15 (using NCS 3.0.1), but I can’t get it to build with `CONFIG_BT_LL_SOFTDEVICE_PERIPHERAL...
Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi,
I've written a nRF51 SWD-JTAG programmer.
I want to enable it to check for minimum softdevice version and error out if a too-old softdevice is found.
It is easy...
I want to communicate four same devices with different hosts. i know that one host can communicate to seven devices and also a device is able to speak different hosts . i...
Thanks for the response. As a test, I loaded the same code onto a PCA10004 and it seems to work as you described. A breakpoint at 217 does get triggered when it receives data...
I have been perusing the source to micro-esb, and it appears that it wants exclusive access to the NRF_RADIO interrupt(RADIO_IRQHandler) and things are designed so that only...
Hi,
i need to save an array of 50 kB on the nrf51822 flash. I only need to read the data stored in the array. I come from the PIC micro world where i simply need to initialize...
Hi,
On peripheral side i have S110 device with ble_bas service and custom base service. Both have notifications.
On centrasl side is S130. After discovering services i enable...
I want to use the pca10001 to communicate as a master to an accelerometer, but when i use the function spi_master_open i get a NRF_ERROR_NOT_SUPPORTED error. I get no clock...
Hi everyone.
I am working with nRF51 to make two BLE device, One act as cetral and another as peripheral.
I have implemented almost functions that the two devices are...
Hi,
Do all NRF51822-DK (development kit) have the same silicon build revision? If not, which distributor should I approach for the latest revision and is there a specific...
I have encountered a problem with the IAR linker where I run into a 32k code-limitaion, even though I have a licence with no limitations. According to IAR, the problem may...
I was playing around with examples and decided to implement a custom service that sends the RSSI as a single-byte characteristic value. Here's the init function:
static...
Hi,
I'm trying to connect to BLE and send data on UART. I'm using nrf51422 with softdevice s310 and SDK v5.2.0.
The following code gives me error 3003 which I figured...
Hi,
I think getting started with the Nordic chips is not as easy as some others.
I would like to know what are the first things that I need to run my code on a Nordic? Especially...
I just got the nRFgo Dev Kit, and going through the set up I see I need a nRF6310 Motherboard, but I can't seem to find anything about it - like were to buy it.
