Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hello,
I am doing some experiments with 2 pca10001 and the ble_hrs example (with s110, s120). As it works well, I would like to mofify this example to fit my needs. I only...
Someone has a working source code (can be Keil format) for the PCA10005 and/or nrf51822-AK (China made) board? I tried the sample at "\nrf6310\s110\ble_app_hrs" but it seems...
The BLE specification core 4.0 imposes certain limitations.
Min connection interval 7.5ms
Data payload on connection 27 bytes (the length field is 5 bits)
What...
Hi all,
I want to add 128bit base uuid for each of my three service,but there is a problem ,I add different base uuid for different service ,but I can only see one base...
Hello,
Please be gentle. This is my first time;) .
I am a retired computer/medical electronics/electromechanical device field engineer.
A friend got me interested...
in sdk 4.3, I used two different ways to know it is read first time(in factory)
NRF_ERROR_NOT_FOUND from ble_flash_page_read to indicated first time it reads
0xff...
I have 3 questions:
1. How to set device to non-discovery mode?
2. Once the device is in non-discovery mode, How can host connect to it?
3. Can I use Master Control Panel...
Hi sir
On your Beacon kit, we found it was used external 32.768KHz at 20ppm.
Question is on iBeacon usage, is a external higher precision 32.768K crystal necessary ? ...
Hello,
I'm working on an ultra low consumption purposes with which NRF51822 commnunique in BT4 with softdevice version 5.2.1.
I compile with GCC 4.7 2013q1. Unfortunately...
Hi
I've have customized a state machine and output patterns for the nrf8002 using the development kit. Now i have my own pcb design and I'm aiming to build a small prototype...
I installed master control panel and plug a PCA10000(usb dongle). The panel discovered the dongle.But once i press "start", an error hanppend:
"ascii" codec can't decode...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi there,
Im wondering if its possible to implement a proximity monitor with the new s120. Having one nrf51822 acting as a central and several (up to 8 I guess) nrf51822...
Hello,
at my current project I send a lot of data from one evalboard to another via proprietary Software.
Now I want to send that data via Bluetooth LE from one evalboard...
