HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
I am evaluating TAIYO YUDEN board EKSHSNZWZ.
I've flashed s132_nrf52_5.0.0_softdevice.hex using nRFgo Studio.
I use Keil uVision to test "nRF5_SDK_15.0.0_a53641a\examples...
Hi. I am trying to transmit a microphone signal to the nrf52832 DK board.
Before development, i checked it by connecting a microphone(ADC) and a speaker(PWM) to one...
It wasn't until I downloaded nRF-Sniffer-v2 that I discover the release note below that explicitly states that nrf_sniffer now supports all platforms supported by Wireshark...
Hi,
We want that any bulb or any devices (Server device) of BLE 4.2 should be able to work with BLE Mesh SDK(Client). We are using the nrf52832 with SDK BLE_2.0.1 for the...
I would like to sample a digital IO input from two IO's into the processor internal memory incrementally per every rising or falling edge of each of the signals.
Is there...
I was trying to follow with the steps in this link: https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
I got an error in the first step while running the setup_sdk...
I have an issue with compilng and loadingthe nrf52840 examples.
I have a nrf52480 pdk and a keil v5 installed on windows.
Everything is ok when I compile and load nrf52840_xxAA...
Hi,
I am using nRF52840 DK which runs blood pressure example. With nRFcloud gateway and nrfcloud.com, I have connected successfully the development kit. Observed that RSSI...
Hi Team,
I am working on nrf52832 for my project.
Please let me know how can i achieve data security in nrf52, What encryption i can use?
Is there any example that will...
Hello,
I'm working on a custom GATT service which has only one characteristic that support notification. The code has started from the ble_hrm service and it runs on a thingy...
Hello,
After having read the documentation of "nRF5 SDK v15" and "nRF5 SDK for Mesh v2.0.1" it is not clear to me which PHY layer it uses at the end.
In the documentation...
Hello,
I am going to use nRF52832, but I have nRF52840 DK, can i use this bord for developing project on nRF52832. Is nRF52840 compatible with nRF52832 in software and hardware...
Hi
I assigned one LED Signal to P0.08 pin in nRF8122 CFAC package as per pin assignment it shows as digital GPIO
But in Firware wise when checking the LED Does not glow...
Dear all,
maybe I‘m missing something, but I know there are OTA DFU client libraries for Swift, ObjC, Java and Python.
But it looks like there is no DFU lib from one...
I was using nrf51822 ,S110 and SDKV10 i had created custom services and its working fine, But when moved to nrf52 DK and S132v5 SoftDevices and SDK version 14.2.0 . same services...