I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
I'm following the tutorial Development with GCC and Eclipse
I could compile and flash existing project that attached to tutorial.
Now I can't understand what to to while...
Q1: how to do network commission? do we have to use an Apps to do commission linke CSRmesh? or it is already in a same network if we configure all nodes use the same access...
I have been using pc-ble-driver in Linux (downloaded and compiled from github here - github.com/.../3316c0c306257a825168751964f814cb95fc0d74) with our custom C++ application...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
Hi All,
I am using nRF51822 for my application.
how to change the App timer Interval dynamically means i have to change the timer interval before timeout.
sdk132. nrf52832 board
Try tutorial "Development with GCC and Eclipse" devzone.nordicsemi.com/.../
.
All the time I'm persecuted by error
/// *** No rule to make target...
I hava a BLE device which can be found by andrioid 4.4 and 6.0 smartphone, but cannot be found by apple iphone5s iOS 9.3, what could be possible wrong with it?
Hello all,
I am using the pc-ble-driver-py python bindings (which depends on pc-ble-driver) to test my BLE peripheral
It works fine for reading and writing characteristics...
Hi,
I use the Current Time Service to get back the time from a smartphone to have a real time clock with a timer.
On the current time service example, the value is read...
Hi:
I compiled the ble_app_cts_c project of the SDK12 using the Segger Embedded Studio having as target the PCA10040 board (S132 stack). After spending some time to convert...
follow the tutorial I'm stuck in the step of removing "retarget"
I don't have such option
I have this one. Should I just remove retarget.c directly via context menu...
main.c Hi,
Currently I am using "ble_app_uart" base example to understand how ble works. I have gone through bsp and other header that related to button events.
There...
Hello developers,
I am trying to use ble_hrm service example with actual heart rate from the module pulsesensor.com ( http://pulsesensor.com/ )
I am able to read raw data...
Hi,
I am working on one application in which I want to change pin number assign to channel 7 of SAADC in nrf 52. I am using Rigado BMD 300 module in my application. As...
Hi,
i want to use a current time service in nordic app (nRF Toolbox) for the bgm profile.
I see, that when the cts service is not found, the micro reset. Why?
Someone...
