Hi,
i want to build a BLE mesh via advertising. i asked some questions before about ibeacon and observer, how ever to clarify my question i have some additional questions...
Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi all, I'm working on experimental_ble_app_buttonless_dfu project in sdk13-alpha using pca10040 board. I just compiled experimental_ble_app_buttonless_dfu successfully for...
Hello all,
I am implementing an energy efficient system, in which I am advertising in BLE_GAP_ADV_TYPE_ADV_SCAN_IND mode, I am using scan_req_report as an acknowledgement...
I'm trying to following example of nRF51_SDK_v12 OTA-DFU Example , but there are no support with BLE400 at all. (BLE 400 has nrf51822 QFACA1 1536EK Chip on it)
I think...
Hi Nordic Team,
Please I would like to ask how can I globally identify my device (nRF51822) based on its address?
Assuming that:
The address type of nRF51 is...
Hi all,
Is it possible to place your own antenna into nrf51822 bluetooth smart beacon kit? if it's possible, how am i going to do it?
am i suppose to remove the antenna...
I made a custom BLE device using nrf51822 and need to do DFU from remote place.
The BLE device is connected using USB to windows PC.
The Serial bootloader examples are...
I am using the nRF52840 Preview DK with BLE 5.0. In the BLE ATT_MTU Throughput Example,I use several api such as sd_ble_gatts_value_get and so on,but i still can not read...
Hello,
I'm using several gpiote interrupts in SDK 12.0.1.
I want to know the max number of low power input pins.
My configuration in sdk_config.h is like below.
thanks...
Hi,
I need to read more than 3 or 4 Bluetooth Heart Rate Sensors (like chest strap, arm band, and so on)... I need to do this using Arduino and some library.
Could someone...
I'm using the ble_app_hrs_adc_battery_measurement example ADC code in my project
However, I don't understand what these lines do
github.com/.../main.c
As far as I...
I am trying to add spi communication to the twi_master_with_twis_slave project because I need to communicate with two different sensors. I have included nrf_drv_spi.h and...
Hi,
in the NRF52832 documentation the TX chain delay is 0.6 µs while the RX chain delay is 9.4µs.
Does that mean if transmitting two packets in a row to the same receiver...
Hello everyone,
I have been using nrf52 IoT SDK for MQTT implementation. Everything works fine as long as I am publishing or receiving only one character i.e.
param...
In Bluetooth Spec (CoreV5.0, Vol6, Chepter6, Section1) it is mentioned that the random private address is generated periodically by a timer handler. I could not find any mention...
1.specification says that we should trigger EP0STATUS task to initiate the status stage for control transfer(read/write).
actually nrf52840 will auto ack the OUT TOKEN...
