Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hi
In my application I have a function that takes about 1 ms, in which timing is critial.
(I cannot allow even a few us change of the timing inside this function).
When...
Greetings, and thank you ahead of time to anyone willing to lend some advice.
I'm implementing application-layer security by requiring central devices to supply a user...
Hi,
I am having some trouble getting the nrf51422 (running the s130 soft device) to wake up after entering sleep mode. I have successfully entered sleep mode using NRF_POWER...
Hi,
I am trying to work with ble_radio_notification.h. When I import this file to my main.c, I have "No such file or directory error". When I try to add it to nRF_BLE folder...
Hii every one,
We are working on a project where we are using a temperature sensor LMT01, its giving a pulse output the pulse out is from 220mV to 600m. So I'm using lpcomp...
Hi,
I am getting only two values on startup and the remaining values as zero when using app_timer_cnt_get.
EDIT: updated entire main.c file
#include <stdint.h>
#include...
I am trying to bring the pc-ble-driver code up on a single processor ARM based board with Linux build under Yocto control. The boost library version being used is 1.60.
...
Hi All,
I'm implementing system clock using approach similar to
devzone.nordicsemi.com/.../
The idea:
NRF_RTC_EVENT_COMPARE_0 -> PPI -> NRF_TIMER_TASK_COUNT
...
I have a nRF51822 custom board for BLE UART application. Connects this to serial port of an ARM SoC board.
P0.09 is for UART_Tx and P0.11 is for UART_Rx. No RTS and CTS are...
i am using a blend micro with nRF8001. and i am using it as a hub in my project.Now i am getting a range of 13 meters.but that is not enough for my project.so can i increase...
Hi!
I'm using the nRF Sniffer software (Windows 1.0.1 Rel.1111) with nRF51-DK Board (Rev. 1.1.0) and Wireshark (1.12.5).
Everything works fine until the number of 65535...
hi
i work in sdk v6.1 and work with dfu over air and it work fine on s110 but now i open this project
nrf51_sdk_v6_1_0_b2ec2e6\nrf51422\Board\nrf6310\s310\ble_ant_app_hrm...
Hi!
Turns out that there is no need for the SD310 and the nRF bootloader. Which means that the flash layout is edited and current support for the BLE OTA is dropped since...
Hi,
I am working on nRF51822 Microcontroller. I am not using any kind of stack I mean Bluetooth etc. I have a simple nRF51822 microcontroller and am running a simple application...
