I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
My previous ticket is closed. I would need, but still help with the configuration of the pins. I report my last post.
Hello, I did some tests with the oscilloscope directly...
Hi,
The previous SDK would allow configuring radio notifications before the radio comms would take place.
I wonder if it is possible to get similar notifications on the...
i have a requirement to connect two nrf52833 boards to connect each other.
(1).if i turn on the Board1 should scan the bluetooth devices if any other bluetooth devices present...
I am working on a proprietary RADIO protocol on the nRF5340 device. Because I'm trying to squeeze as much throughput as possible out of the RADIO I would like to be able to...
I am developing my first BLE Server application with the nRF52832 and using VSC/nRF Connect/Zephyr ROTS. I come from a Cypress/PSOC Creator background, and am struggling a...
Hi DevZone,
I recently updated my version of SEGGER Embedded Studio for ARM to v6.20. Now, warnings that were not shown before are caught.
I want to ignore the warning...
Hi Nordic, Currently my project is using SDK 15.3. By taking a look at NCS SDK, I can see lots of features there and plan to migrate my project to NCS 1.9.0. However, since...
The NRF5340 net core crashes in sdc_hci_cmd_le_set_adv_enable() if I have CONFIG_CLOCK_CONTROL_NRF_CALIBRATION_MAX_SKIP set to 0.
To reproduce the issue, do the following...
Hi ,
I am using nrf52833dvk and nrf52832 boards, am working on application that my nrf52833 board do the firmware updation of other board i.e. nrf52832 . first time i did...
We plan to incorporate the nRF9160 into many thousands of our devices, however this leads to a question of procuring SIM cards. We purchased a Thingy91 to test the connectivity...
The iBASIS sim card came with Thingy:91 does not work. Got the replacement card today. However, I cannot finish the nRF cloud reg process. The new error message said
Tenant...
Hello, I am trying to load a sample project in VS Code using the nRF Connect SDK extension.
I try to load a sample project, click on "Create Application", and nothing...
I am trying to use the NRFx Softdevice controller, with Rust and the nRF5340. I have successfully initialized the library, but when I try to start to start advertising the...
Hi! I'm unable to connect my development kit to a network with the provided iBasis SIM card. I'm located in Bristol UK. According to this [ https://ibasis.com/solutions/iot...
To provide feedback to the user through the LED state, I would like the behavior to be something like this:
If the nRF52840 Zigbee device is unpaired and ready for a ZC...
