Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi,
I want to use a TSOP IR receiver on a custom board for sending different commands to my device through a remote controller. for example, if I use a Samsung TV controller...
I want to configure the NPM1100 to work with either rechargeable or non-rechargeable batteries (in factory).
Would it work to set mount a suitable resistor to the NTC pin...
Hi,
We are evaluating thread. And would like to build a basic demo app using a thread border router and a few sensors. We got the border router working with the coprocessor...
Hi,
I am using nrfconnect sdk with central_uart example. How to get the name of the device
advertise the BLE discovery packets? nrfconnect android app shows the name after...
Hej!
I see that the CRC block is used in the Radio under section 23.6 of nRF52832_PS_v1.4.pdf . Also, I noticed that the CRC32_ENABLED is only enabled in the bootloader...
My previous ticket is closed. I would need, but still help with the configuration of the pins. I report my last post.
Hello, I did some tests with the oscilloscope directly...
Hi,
The previous SDK would allow configuring radio notifications before the radio comms would take place.
I wonder if it is possible to get similar notifications on the...
i have a requirement to connect two nrf52833 boards to connect each other.
(1).if i turn on the Board1 should scan the bluetooth devices if any other bluetooth devices present...
I am working on a proprietary RADIO protocol on the nRF5340 device. Because I'm trying to squeeze as much throughput as possible out of the RADIO I would like to be able to...
I am developing my first BLE Server application with the nRF52832 and using VSC/nRF Connect/Zephyr ROTS. I come from a Cypress/PSOC Creator background, and am struggling a...
Hi DevZone,
I recently updated my version of SEGGER Embedded Studio for ARM to v6.20. Now, warnings that were not shown before are caught.
I want to ignore the warning...
Hi Nordic, Currently my project is using SDK 15.3. By taking a look at NCS SDK, I can see lots of features there and plan to migrate my project to NCS 1.9.0. However, since...
The NRF5340 net core crashes in sdc_hci_cmd_le_set_adv_enable() if I have CONFIG_CLOCK_CONTROL_NRF_CALIBRATION_MAX_SKIP set to 0.
To reproduce the issue, do the following...
Hi ,
I am using nrf52833dvk and nrf52832 boards, am working on application that my nrf52833 board do the firmware updation of other board i.e. nrf52832 . first time i did...
We plan to incorporate the nRF9160 into many thousands of our devices, however this leads to a question of procuring SIM cards. We purchased a Thingy91 to test the connectivity...
