Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi there, I'm using nrf52840 with OpenThread SDK and I wanna know, what is default radio mode of this device? Because we also have another project with Bluetooth and we observe...
SDK15.0 whitelist hardfault
when setting the sd_ble_gap_device_identities_set using the iOS nrfConnect the non DK board hardfaults.
On an android device all works fine...
Hi,
I'm adding some custom buttons to the NRF52-DK and I've been playing around in PCA10040.h. So far, I have everything working with 4 buttons. The DK can connect to...
Dears,
Now I am using nRF5_SDK_15.3.0_59ac345 for my project on nRF52810.
I found a bootloader example at
\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040e_ble...
hello, I am trying to integrates saadc & bluetooth because in my project adc sample values are comming from sensor & these values is send through bluetooth_uart app. so can...
Hi,
I'm in the process of evaluating the nRF9160 DK and this I want to be able to control the diferent peripherals on the DK so I can reduce as much as I can the current...
Dear supplier
I want to read 10 heart rate sensors that are connected to 10 person's bodies and then display them on TV. How can I do it?
Can I use nRF52832 chip? Can...
Hi
I am using nRF5_SDK_15.2.0_9412b96 on pca 10040
I am storing over 2000 ADC readings and then printing them out once my test is complete. I get "Logs Dropped(x) " messages...
Hello
I am writing a program using SDK 15.0.0.
I'm trying to merge SPI and TWI programs into BLE programs.
I used keil before to confirm that each program was working...
Using Ozone v2.54, if i halt program execution and then resume again, I get a NRF_FAULT_ID_SD_ASSERT fault, with info = 0, pc = 0x142CA.
softdevice: s132 v4.0.2
The error...
Hello ,
I am using Multiperipheral example code , and i want to connect more than 4 central devices. I have edited the link total value and number of peripherals and centrals...
HI,
I am recently working on 9 axes icm 20948 sensor. my battery capacity is small for the application and my accelerometer and gyro sensor consumes more current.
when...
when ble central set BLE_GAP_IO_CAPS_DISPLAY_ONLY ,i find ble central no need to send the static passkey or send one wrong static passkey,ble central can also connect ble...
