I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi !
I'm using the nrf52832 with SDK 11 as pheripheral.
In Android phone the bonding and the scan request working great with my unit !
However, in IOS
1) i do scan...
Hello,
I am working with LPN example of SDK 3.1.0. In the example I need to change the poll interval time based on our application requirement.
I looked at this equation...
Hi Nordic team,
I have a curious problem I need a little help with:
(NRF52840 & SDK 15.3)
I have a project which is an integration of the ble_uart example and the serial_uartes...
I have searched your forum and have found several references to my issue; however, I have not been able to get anything resolved.
I am using the nRF51822 which is part of...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
I have gone through “Application Timer” tutorial...
I have a development board and load the client central BLE blinky to it, then the peripheral BLE blinky to my custom board and power up and the central development board stays...
I was wondering if it is possible to do HTTP requests with the nRF9160 just by using AT commands? Since this is usually possible with such kind of modules.
The reason is...
Hello everyone,
I've got a three type of devices: 1 Central device, 2 Peripherial devices, and mulitple beacons. Central is connected with two peripherial devices with...
Hi Devzone,
We are using the nRF52 DK in a prototype which is under stress, and we noticed that any bending of the board breaks the BLE connection.
To easily replicate...
Hello,
I am currently writing a script whose purpose is to automatically provision and configure devices.
My question is related to the devkey_handle and address_handle...
With SDK 14.2.0 and S332 softdevice, I'm using UART to control ESP8266 WiFi module with AT commands and I'd like to replace app_uart (+FIFO) with nrf_serial , in order to...
Hi,
I am setting OOB with sd_ble_gap_auth_key_reply() method { 0x11, 0x11, etc 16 bytes }, but when trying to connect with desktop nRF Connect there is an error 132 inside...
Hi,
I am getting errors when attempting to include the nvs library to save data to flash storage on the nRF9160 DK. My CMakeLists.txt:
I get the same errors with or...
Hi,
We tried to use a smartSIM from Sierra Wireless with the nrf9160DK without success.
The nrf91 can connect to the LTE network after a few minutes (LED4 steady). However...
