Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
We have implemented DFU services in application but getting lots of difficulties for writing own transport layer for Wi-Fi to upgrade firmware from server. We are...
Hi...
i have done the program to read the temperature sensor, i want to get the temperature in float value . i can able to read the temperature in float but i can't able...
Hello Nordic Pro's,
We are developing a product based on the BLE UART peripheral. We communicate heavily via NUS. There are extended processes that continually send status...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) As per below link, do I need to skip GPIO...
I would simply like to see the debug outputs (NRFX_LOG_DEBUG) the NRFX_TWIM.C module using RTT debugger through Segger J-LINK.
I cannot find any documentation on how to...
Hi,
I am working in nRF52832 SDK15.3 in SES
I need to work on reading multiple Analog inputs. in a different timings.
i have seen SAADC example.
is there any multiple...
Hello,
I am working with nRF52832 , a soft based on the NUS service and SDK 15.2 ( S132) .
In the aim of reducing the current comsumption , I want to modify the throughput...
Hi Martin, I follow all the steps in your tutorial(Bluetooth low energy Characteristics, a beginner's tutorial) and I am able to create the characteristics and the notification...
How do I share variable data from my nRF52 application to the bootloader code?
Check the update to this question after first comment by @HungBui
There is some short...
Hi,
I am using three nRF DK (nRF52832 - PCA10040) to test and analyse the mesh network (nRF5 SDK for Mesh v3.1.0).
I worked on light_switch_example with 2 clients and...
Hi.
I'm using the nRF52810-QCAA (DCDC) Reference Design, but I've noticed that C6 and C13 are labeled as No Connected in both the schematic and BOM, but in the PCB model...
Hi,
I am trying to write data to the nRF52 module from my custom application. I am sending few parameters bundled into a packet to the module. One of the parameters is the...
Hi
Im currently having some problems with programming a solution for a small system that im making.
The idea is a mailbox with a dongle and accelerometer that senses movement...
Note that for SDK v12.3 : if application size * 2 > available space a single bank update is performed.
While I am using v15.3 and there seems no more infor about the single...
I installed espruino_1v99_thingy52_app and espruino_1v99_thingy52_softdevice , but i want to restore the thingy to the default firmware. Have a way to reverse to the default...
