after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
System details:
Board: Custom
Chip: nRF52832
PCA Number: PCA10040
SoftDevice: S132
SDK: Version 16.0.0
Until recently, I have had no issues using the TWI module...
I use nRF52840 in aQFN73 package. Can I assign QSPI contacts to G1, J1, L1, N1, R1, U1 pins? Or should I strictly follow the recommendations from the datasheet? Thanks.
Hi All,
I have an application that wants to send 1 array every 2ms. There are 10Bytes of data in the array.
I will be based on 1Mbps, MTU size = 23byte, Payload = 27byte...
Dear Sirs,
I use the standard printf() function to communicate via UART (with retargeting).
Unfortunately could not find a way to not overwrite a buffer.
The only workaround...
I have configured EasyDMA RX.MAXCNT=256 and set EVENTS_ENDRX. If >=256 bytes arrive, an interrupt occurs immediately. And if only 128 or 10 or 203 come.. byte, then I'll never...
Hi,
I'm using nRF Connect SDK 1.7.1.
Is it possible to mix polling & interrupt driven UART API?
I have a situation in which I want to receive input once in a while...
Hello,
I am using the Bluetooth Low Energy application to interact with my device under development. I notice that if I set the Write No Response property on an attribute...
Hello, I have recently started an evaluation on nRF9160 DK in the UK. I tried to run the Serial LTE or AT Client examples but I was not lucky to register to a network. Using...
Hi to everybody, i'd like to know if there is a way to enable/disable mesh message relying on a node locally by the firmware without using a configuration client or a provisioner...
Hi Nordic, Since the last update of the Programmer application of the NRF CONNECT for Desktop, I've been seeing this error: I've NRF52833DK // PCA10100, and up there it says...
Hi Sir/Miss,
I use programmer v2.3.1, J-link and nRF52810.
After I connect to J-Link which displays nRF52840 in UI. In log windows, it's normal.
Please check below...
I have been writing an app and now changing the bluetooth library to Nordic Android BLE Library. W hile connecting to the device I keep the autoConnect flag on, which lets...
Good morning/afternoon/evening to whoever is reading this.
I am fairly new to working with nRF tools, this is in fact my first time working with this. I have a linux virtual...
Hi,
Sdk-17.1.0
Soft device-s112
I have large amount of sensor data in my memory (eg:- 8MB of temperature sensor data, 100000 readings). I want to transfer this to the...
When the nRF52840 Dev Kit is sending data as a peripheral, connected to client running nRF Connect all works.
I am sending (streaming) a text file to iOS phone or Android...
