Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi all,
I’m working on a people tracking system using the nRF52833 module , and as I’m new to this, I want to start with a proof of concept (POC). Here’s my current plan...
Hi,
I have a root certificate that is used by the popular TLS certificate service Let's Encrypt that fails to parse in NCS 2.6.0 on the nrf9160dk. You can find the certificate...
I am looking for an example 6 layer stackup for the use of the nRF5340 / nRF7002 combo that has been proven producible by pcb manufacturs. The nRF5340-QKAA requires microvias...
Hello, We designed and tested a firmware on the nRF52833-DK board, whith plenty of debug sessions and reprogramming. Then it has been build for our custom board, based on...
Hi all,
i am trying to update the nrf5340 firmware using STM32 as the master controller via UART. i initially tried to upload the .bin file of my project to nrf5340 using...
Hi Nordic Team,
I am working on a project where I am using an XBee module as the Zigbee coordinator in a centralized network and an nRF52840 (running the ZBOSS stack from...
Hi everyone, I have a problem when I configured custom board GPIO UART in NRF54L15. I know that the NRF54L15 have UARTE00, UARTE20-22, UARTE30. I just use 2 GPIO ( UARTE20...
I use the app_gpiote_user_register to set GPIO port 1 pin, but this registers only 32-bit mask, so it can only to setting port 0.
If I want to use the port 1 pin for app_qpiote...
Hi!
I'm attempting to run the application from this URL , but nothing appears on the serial console, and I don't see any posts on the toilet website.
Could you help me...
Hi,
I am using an nrf5340DK + nrf7002EK. i am able to run an example helloworld application with an immutable bootloader and mcuboot as platform bootloader. When i try to...
Hello! Recently while performing a BLE firmware update using the mcuMgr Library, the stages of the firmware update are as follows VALIDATE, RESET, and fail on UPLOAD. When...
the code below successfully complies and returns 3 services with 1 characteristic each, I have copied the uuid for the primary services and characteristic and that doesn't...
Our board is based on nRF52833, using SDK 2.1.2, Zephyr 3.1.99 Project is configured to enter low power mode for both CPU and peripherals CONFIG_PM=y CONFIG_PM_DEVICE=y Our...
