Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I'm using the power profiler to perform current measurement of our IoT device. It appears to work well when running for a few minutes capturing. When I wrong for...
I am trying to use SPIM2 on an NRF52840 based board. The SDK is 17.0.2.
For the life of me I cannot understand how to 'consistently' determine the values to be specified...
I'm trying to modify the HTTPS sample to connect to Google Cloud Functions but I keep running into this issue where connect would fail.
1. I have disabled TLS peer verification...
We have a running project with nRF52840 + S140 7.2.0 - SDK: 17.0.2 + Bootloader.
I need to change the size of our bootloader in a production environment. This update must...
Hello,
We are currently certifying our module for Verizon in the US. As such, we are updating our software to work with MFW v1.3.0 and the corresponding NCS version v1...
Dear Nordic,
we developed firmware based on S112 and SDK 17.1.0. We have a problem with poweroff routine: at poweroff the status LED is ON.
this is part of our circuit...
Hi Team,
I am using nRF52840 on our custom board. I have enabled SMP for DFU and SMP image management in my build. DFU was successful for the 1st time but when I try to...
Hi,
I have my programming environment set up to use the nRF Connect SDK through VS Code, as the most recent documentation suggests. I can successfully build and flash code...
Hi ,
How we can achieve the right and left align for the data buffer register for the nordic as well as zephyr ? any sample example where this option we can achieve.
Dear friend,
How much RAM does ECB encryption consume? Currently implemented using a third-party AES library (consumes 2.3k of RAM). Is there a way to encrypt that consumes...
Hi community,
I was changing the IDE from SES to VS Code and got everything running fine except debugging.
If i execute VS Code as administrator debugging works as supposed...
Hey guys,
i tried my best did my own research, but i can't get it to work.
I'm trying to manually add .c and .h files to a project in Segger Embedded Studio ialso put...
The following instructions are for using Segger Embedded Studio to flash the dongle.
https://devzone.nordicsemi.com/guides/short-range-guides/b/getting-started/posts/nrf52840...
Hi,
I have changed the vendor model for sending data from client to server in light switch example. Earlier it was just sending bool values. I have changed it to uint8_t...
