Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Can you confirm the appropriate method to doing AFC correction for a GPS SNR test using the %XRFTEST command and then using the AFC correction result in the GPS SNR...
I use SPI to develop motion sensors KX022 and DW1000. The first digit of the received data is always 0xFF. If the first byte received is removed, it can be used normally....
I am trying BLE MESH light switch example with nRF5_SDK_for_Mesh_v5.0.0_src using nRF52833 DK. In the light switch example, server SDK is working fine and I can see the provisioning...
Hi All,
I am using Custom 128-bit UUID, My application need 3 Custom Services and 20 characteristics. But I need to make different Base for services and characteristic...
Hi,
I recently installed v1.9.0 SDK and while creating project from sample applications I am getting below error.
Attached is build logs from segger IDE.
Can anyone...
I'm looking to build a custom bootloader for my NRF52810 device. I'm developing on nrf sdk 17 with SD 112. I will be leveraging the secure bootloader example and re-using...
Hi;
i am using sdk 17.0.2 and mesh 5.0.0.
i am using light switch instance.In addition, the system works properly when provisioning is made with a smartphone.
I want...
I am using VSCode and the NRF Connect SDK
I can build and flash my device however i keep getting cannot open source file for all my includes, i also cannot navigate to...
First, NRF52833 work environment at 100 degrees celsius, standby current reaches 60uA.
Second, When the NRF52833 working in 100 degrees Celsius, what kind of processing...
I have a secure BLE DFU project that is basically a duplicate of the example project (secure bootloader pca10040_s132_ble). I am able to flash a merged hex on my custom board...
I generate the hex file for a release and then tried to rebuild it in a different folder. This is to ensure that all the required files are checked into the archive system...
Hi,
We are developing a firmware using the nRF52 DevKit as a reference, as well as its companion iOS Application.
Pairing & Bonding:
We have successfully integrated...
Hello !
I have evaluated AES-CCM co-processor in on-fly and from memory-to-memory encryption/decryption operations and see it works in BLE 2Mbit mode without visible problems...
I can not seem to figure out why when I init the advertising and then issue a start to the advertising the advertising beacon shows up as a connectable when viewing under...
Hello,
I am using SEGGER Embedded Stuido for ARM(Nordic Edition) V5.68 for NRF9160 evaluation.
It was Okay for while. But, suddenly, I met error message(SyntaxError...
