Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hello team,
I successfully migrate from the SDK 2.6.1 to 2.9.0.
Now, I am trying to build the modem_shell sample for the nrf9160DK with nrf9160dk_nrf9160_ns .overlay file...
Hi, I'm using ezurio BL653µ and want to create a custom board in ncs2.8.0 (HWMv2) but i cannot sellect the nRF52833-CJAA variant. What do i do? Do i select another variant...
We are considering to implement ”ASCS/BAP/CAP/CSIP/PACS” as the BLE profile.
Do you have any QDID for this profile certified in SDK 2.3.0? If yes, please provide each of...
Hello,
I am completely new to Nordic eco system. What I basically want to do is make a simple bluetooth mouse using a module and the Connect SDK with the HID sample.
Now...
Hi team,
Linking error for ble_uart
Segger embedded studio - 8.22a.
SDK version - 15.0.0
error -
Building 'ble_app_uart_pca10056_s140' from solution 'ble_app_uart_pca10056_s140...
nRF52832 is used as Central to get data from nRF52820 (Peripheral).
There is no problem when you always communicate, but if you can not communicate due to running out of...
I have a project using ncs 2.7 with the nrf9160. My west manifest file is set up to import all and it takes forever, so I am trying to narrow it down to only what is needed...
Hello, Currently i am working on ble mesh and specifically on different nodes implementation, Proxy node, LPN node, Friend node. But when i am starting to implement and testing...
Hello,
i am using the Wi-Fi: Scan sample with the nRF 7002 Deveolpment Kit.
I am trying to alter the clock frequency/QPSI mode (Dual/Quad) of the QSPI Bus connecting the...
Hi. I am using nrf52832 and 17.0.2 sdk.
What I want to do is to provide automatic connection between my nrf device and my android device. For this purpose, I use the HID...
I'm trying to use AAR peripheral, but I don't know the structure of output DMA job list, as it's not defined in the datasheet. I was trying to use one job pointing to flat...
Hi,
I'm transmitting using the nRF24L01P and using the nRF52810 as the receiver, 5 byte address.
We send a 2 byte packet usually 0x00, 0x00 until data is ready. If I set...
BT_DRV_RX_STACK_SIZE is too small and can't be configured. It needs to be more than 512 bytes in released versions of Zephyr, or 640 bytes, on the main branch. Note: I'm using...
Good morning everyone,
I am going crazy to solve this problem, but I hope we can figure it out with some help.
I am working on a prototype for which we need to use a...
The documentation for the Maximum Performance sample mysteriously states that the sample is not supported on the 5340 with no explanation as to why. As I am getting spurious...
