I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hi,
I have changed the vendor model for sending data from client to server in light switch example. Earlier it was just sending bool values. I have changed it to uint8_t...
Hi,
I try to write in flash with the flash_manager. I use this code to write in the flash.
Everything is fine when the flash writing succeed. But when a issue occur in...
Hi,
I'm using nRF9160 and want to use PWM with the automatic duty sequence feature using DMA, to make an LED "pulse" for example.
Looking at the documentation for the...
We recently bought a nRF9160 Eval board and are planning to connect it with a STM32H757XI_M7.
We would like to know, how well it can be integrated with the IwIP Stack...
Hi Nordic,
I am using the SDK 17, s140 and the nrf52840 , with a modified multilink NUS central example. The intention is to print over UART as fast as possible all data...
Hi All,
I have a nRF9160 custom board connected thru the P19 debug out connector to the NRF91DK board.
How do I 'make' the NRF91DK debug the custom board nRF9160 and not...
Hello. I have a custom board which contains S32K148 MCU and Murata MBN52832 BLE Module and several other modules like GPS, LTE etc. Board is powered via external 12 V adapter...
Hello. It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to know the handle value of the characteristic set as Generic Access and...
Hello,
We have a bunch of demo devices that were populated with the nrf5340 eng A version. So far we have been able to make them work by using nrf connect SDK v1.4.0 which...
Hello
We want to use the Gazell protocol into an Arduino IDE based firmware project.
Therefore I would like to know if you have any advice, documentation, examples, etc...
Hi
What is the max size of RAM and Flash for APP?I looked in the partitions.yml of a sample，I found that there is many region for different use，I don't know which region...
Hello,
Please share any working document to enable UART2 for external communication. I gone through many documents and forum and many setting in prj.conf but still no results...
I have 2 devices in the same SPI bus defined in my devicetree. let's call them MAX30005_1 and MAX30005_2.
When the drivers initialize, they read a register of the device...
Hi Folks,
As per bluetooth spececification(4.4.2.2.1) advertising interval has addition of advDelay in range of 0-10ms. In my example,
1. device advertise beacon (sd_ble_gap_adv_start...
Development Kit: NRF52840
IDE: Segger Embedded Studios
I'm trying to use the nrf_drv_twi driver in my project. I've included the .c file in my nFR_Drivers folder. My...
