Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
The following instructions are for using Segger Embedded Studio to flash the dongle.
https://devzone.nordicsemi.com/guides/short-range-guides/b/getting-started/posts/nrf52840...
Hi,
I have changed the vendor model for sending data from client to server in light switch example. Earlier it was just sending bool values. I have changed it to uint8_t...
Hi,
I try to write in flash with the flash_manager. I use this code to write in the flash.
Everything is fine when the flash writing succeed. But when a issue occur in...
Hi,
I'm using nRF9160 and want to use PWM with the automatic duty sequence feature using DMA, to make an LED "pulse" for example.
Looking at the documentation for the...
We recently bought a nRF9160 Eval board and are planning to connect it with a STM32H757XI_M7.
We would like to know, how well it can be integrated with the IwIP Stack...
Hi Nordic,
I am using the SDK 17, s140 and the nrf52840 , with a modified multilink NUS central example. The intention is to print over UART as fast as possible all data...
Hi All,
I have a nRF9160 custom board connected thru the P19 debug out connector to the NRF91DK board.
How do I 'make' the NRF91DK debug the custom board nRF9160 and not...
Hello. I have a custom board which contains S32K148 MCU and Murata MBN52832 BLE Module and several other modules like GPS, LTE etc. Board is powered via external 12 V adapter...
Hello. It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to know the handle value of the characteristic set as Generic Access and...
Hello,
We have a bunch of demo devices that were populated with the nrf5340 eng A version. So far we have been able to make them work by using nrf connect SDK v1.4.0 which...
Hello
We want to use the Gazell protocol into an Arduino IDE based firmware project.
Therefore I would like to know if you have any advice, documentation, examples, etc...
Hi
What is the max size of RAM and Flash for APP?I looked in the partitions.yml of a sample，I found that there is many region for different use，I don't know which region...
Hello,
Please share any working document to enable UART2 for external communication. I gone through many documents and forum and many setting in prj.conf but still no results...
I have 2 devices in the same SPI bus defined in my devicetree. let's call them MAX30005_1 and MAX30005_2.
When the drivers initialize, they read a register of the device...
Hi Folks,
As per bluetooth spececification(4.4.2.2.1) advertising interval has addition of advDelay in range of 0-10ms. In my example,
1. device advertise beacon (sd_ble_gap_adv_start...
