I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello Team,
We are using custom nRF52833 with nRF21540 (PCB). we manually controlling the nRF21540 FEM using GPIO and SPI (not using the FEM driver) for testing purpose...
Hello
On my application I have noticed that when I use hardware flow control of the uart1 (not the console uart) the processor will get stuck just before the application...
I want to use a hardware encoder to implement a mouse scroll wheel. Do you provide a QEDC routine for me to quickly learn and use? Are there any specific pin requirements...
I've had problems during installation probably due to firewall/proxy/network protection, so I managed to install from command line as specified in Installing the nRF Connect...
I have a couple of questions regarding the operation of the nPM2100 when using the LDO in Ultra-Low Power (ULP) mode, both in active and hibernate states.
Active Mode...
I used the Nordic plugin in VS code to open the process very slowly, and the build is also very slow, it takes a few hours, I have reinstalled VS code, I have also re-downloaded...
When configuring the Bluetooth protocol for NRF5340-CLLA, should I use nrf5340dk/nrf5340/cpuapp/ns or nrf5340dk/nrf5340/cpunet when adding the build configuration, or do I...
When using the nrf52832 to scan and connect to a BLE central device, the first connection is successful. However, after the first connection is disconnected and I attempt...
Hi,
We’re developing a BLE-based product on the nRF54L15 (InsightSIP ISP2454-LX) using nRF Connect SDK v3.0.2 , with MCUboot enabled for DFU.
Our BLE application is based...
I have a custom board using a nrf5340 and am getting a 1 when trying schedule delayble work and I can't figure out why. I isolated the code to test which gets called from...
I recently updated VS Code and regret doing so. My SDK 2.3.0 was working fine for over a year. But VS Code keeps prompting me with an update. I finally updated it and I can...
I want to use the async driver,but did not find the example or explanation.
I have looked for the whole examples with "nrf_libuarte_async.h", found nothing,a little strange...
Hi, The latest version of the NRF connect VScode extension uses forward slashes in paths, which break pristine build on Windows.
The path to my sources has /V in it which...
I want to control RADIO using the TimeSlot API of nRF54L15. I have already created the code for nRF52. However, it seems that RADIO control of nRF54L15 is slightly different...
