I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
We have implemented DFU services in application but getting lots of difficulties for writing own transport layer for Wi-Fi to upgrade firmware from server. We are...
Hi...
i have done the program to read the temperature sensor, i want to get the temperature in float value . i can able to read the temperature in float but i can't able...
Hello Nordic Pro's,
We are developing a product based on the BLE UART peripheral. We communicate heavily via NUS. There are extended processes that continually send status...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) As per below link, do I need to skip GPIO...
I would simply like to see the debug outputs (NRFX_LOG_DEBUG) the NRFX_TWIM.C module using RTT debugger through Segger J-LINK.
I cannot find any documentation on how to...
Hi,
I am working in nRF52832 SDK15.3 in SES
I need to work on reading multiple Analog inputs. in a different timings.
i have seen SAADC example.
is there any multiple...
Hello,
I am working with nRF52832 , a soft based on the NUS service and SDK 15.2 ( S132) .
In the aim of reducing the current comsumption , I want to modify the throughput...
Hi Martin, I follow all the steps in your tutorial(Bluetooth low energy Characteristics, a beginner's tutorial) and I am able to create the characteristics and the notification...
How do I share variable data from my nRF52 application to the bootloader code?
Check the update to this question after first comment by @HungBui
There is some short...
Hi,
I am using three nRF DK (nRF52832 - PCA10040) to test and analyse the mesh network (nRF5 SDK for Mesh v3.1.0).
I worked on light_switch_example with 2 clients and...
Hi.
I'm using the nRF52810-QCAA (DCDC) Reference Design, but I've noticed that C6 and C13 are labeled as No Connected in both the schematic and BOM, but in the PCB model...
Hi,
I am trying to write data to the nRF52 module from my custom application. I am sending few parameters bundled into a packet to the module. One of the parameters is the...
Hi
Im currently having some problems with programming a solution for a small system that im making.
The idea is a mailbox with a dongle and accelerometer that senses movement...
Note that for SDK v12.3 : if application size * 2 > available space a single bank update is performed.
While I am using v15.3 and there seems no more infor about the single...
I installed espruino_1v99_thingy52_app and espruino_1v99_thingy52_softdevice , but i want to restore the thingy to the default firmware. Have a way to reverse to the default...
