Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
The chip I am using is 54l15, and the NCS version is 2.8.0
I used the peripheral_uart example for modification and got my own program, but I forgot which time this problem...
Hi Nordic
Asking this question to Nordic AI (right-down window), below was the answer.
The nRF9160 is a cellular IoT device, and its MTU size depends on the protocol...
I am programming a RAK4631 Board, which is of course based on the nrf52840 SoC. The BaseLine Device tree has no detail in the ADC Node so I have created an overlay. The RAK4631...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
The design has an eSIM and a regular SIM, with a switch driven by a GPIO line. We default to the regular SIM, but if the library...
Hello,
How can I check which crystal oscillator is configured for the nRF52832 DK from the firmware side? Is there a specific configuration file or parameter that defines...
Hello,
I have a Python script that analyses some sensor data. If a condition is met I want to send a trigger via ESB to a peripheral board (ESB chosen for its low latency...
Hello, I'm having issues when building the peripheral_nfc_pairing and central_nfc_pairing samples from ncs 2.2.0 in VSCode. I've build before and haven't gotten any errors...
Hi,
I’m currently working on a Zephyr project using the nRF Connect SDK, and I am looking for a way to setup the toolchain for my terminal emulator (specifically using zsh...
Hi
I'm new on zephyr and nRF9160.
In the nrfx source are lots of NRFX_ASSERT() macros.
This macro checks a condition and thrown a exception.
Normaly we use asserts...
Hello everyone,
We are using the NUS service to transmit some data. To comply with certain CEM tests and regulations, we need the ability to configure BLE to publish on...
Hi,
I'm working with the nRF21540 Development Bundle (DB) , which includes the nRF21540 DK and nRF21540 EK . I need to use the FEM module with the GPIO+SPI interface to...
As title says, I have a clean install of Xubuntu 23.10, latest nrfutil and toolchain-manager package
My shell is zsh, however "nrfutil toolchain-manager launch --shell zsh...
Hello, I'm trying to get FOTA over BLE (SoC & external Flash) working on NCS 2.9.0. The sysbuild and MCUboot configurations and overlays seem to be fine. The application builds...
