I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi, after uploading a Zephyr project (like the "Hello World" example), I couldn't see the device in the serial monitor. i add the below commend in overlay file also but still...
Hello,
I am in the process of following a series of tutorial videos on driving an LED with pwm, but I don't understand how to properly configure my .overlay file and my...
Hi,
I am developing an application for an nRF52840 using nRF Connect SDK v2.9.0. The application currently uses the Zephyr driver for simple PWM functions on several GPIOs...
Hello,
I'm using 'nRF Connect for Desktop v4.2.0' and 'nRF Connect SDK v2.3.0' on windows 11.
I was using vs code well for developing nrf52840 board.
But, I found...
Hello!
I'm currently testing writing and erasing data to an external Flash using an nRF5340 and a NOR Flash, the mx25r64.
I'm going to use the SPI_FLASH example.
I bulid...
Hi,
I need to read 16-bit values from a sensor using SPI on the NRF52840. However, since the SPI peripheral only supports an 8-bit word length, what is the best way to handle...
We have nRF5340 LE Audio dks. We intend to check the PDUs transmitted. Does wireshark nrf sniffer support this if yes then how and if not then what is the possible way to...
Hello I want to operate one RGB LED SK6805-EC10-100 for that i need to write data bit by bit in between need to use some delay if any API is there please let me know.
...
Hi,
I noticed that the f_sector_cnt element of the fcb struct is a uint8_t .
How is that supposed to handle large flash sizes? I mean even with a sector of 64KB, the FCB...
Hello Nordic Semiconductor Community,
I am currently working on a project using a custom board based on the E73-2G4M08S1C SoM, which features the nrf52840 chip. For flashing...
Hi
What is the timestamp accuracy of the nRF51 DK based Sniffer, nRF52 DK based sniffer,
I want to measure the actual accuracy of my advertisement interval, preferably...
I’m working on a device using a Nordic chip and the following setup:
nRF Connect SDK : v2.5.2
Toolchains : v2.7.0
We need to minimize current consumption during...
Hi,
I updated my NCS to V2.9.0, I try to build my project, but it fail(it's OK at V2.8.0). the output message (attached file); Please help to check the message , how can...
Hello!
I have been testing the distance measurement functionality on the nRF52832, and it performs up to approximately 10–12 meters in an office environment. Switching to...
