I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Good afternoon,
I am working with the Thingy:91 platform and I would like to know if it is possible to get the GPS position without internet connection and if there is any...
Hi Team
1. are the following phy layer parameter like SNR,RSSI available for both WIFI and BLE?
2. if so, which register to look for such information
3. Also how about...
Hello
I am getting started on nRF SDK and I went through all the examples (at least those I'm interested about) successfully.
Now, I need to merge couple of examples together...
Hey
When i disconnect my nRF5340-DK devkit to my Lenovo T14s Gen 2 running Ubuntu 20.04.3 LTS the usb driver in the linux kernel crashes.
I think it's a problem that...
Hello there,
I've set up a Thread network with a few devices, and now I would like to connect to a ipv4 server.
At home or at the office we do not have a ipv6 public address...
Hi,
We are Migrating from nRF52832 to nRF5340 dual-core soc. In nRF52832 9 off available GPIOs were only to use with a low drive, low-frequency application since they may...
I have starting working with UART. I see that there are two options for configuring it: UART_0_ASYNC and UART_0_INTERRUPT_DRIVEN. I want to use ASYNC option for my UART, but...
Hello
NCS1.8.0 Windows10 X64;
Can [v1.8.0\zephyr\tests\drivers\adc] convert microphone analog signal into digital signal? for I2S 8bit 8kHz
thanks
Best Regard...
Hi, I need to fetch the Device ID of nRF5340 Chip. In datasheet Info.DeviceID[n], n = 0...1 , is mentioned. How to access this information ? Also, I am using nTF5340-DK kit...
Hello
I am planning to purchase Nordic Semiconductor Power Profiler Kit. Before purchasing the kit I need to know, Is this kit supports another company's microcontrollers...
I am using nrf52832 with a custom board with no external crystal oscillator. As bootloader I use "secure_bootloader_uart_mbr" so I don't have softdevice. SDK is 17.1.0_ddde560...
using ble_app_interactive on one dev kit and connecting to pc viewing on terminal
other is my perihperal.
on entering connect <device address> it gets disconnected
hi I sucessfully tested the blinky project on the nRF52840 dongle... btw i'm using vanilla zephyr...
but i'm unable to prototype the uart comm on this board... the board...
I'm working on NCS 1.8.0.
I can use DFU APIs to upgrade my firmware successfully, however, after DFU is finished and system reboot, the McuBoot to swap images is too slow...
