Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
I ran into a problem. I am unable to disable or reconfigure UART1. Any changes to the file .overlay does not give effects. I paste into the file nrf9160dk_nrf9160_ns.overlay...
Hello,
I am using an nrf52832-based ble chip and try to communicate with cap1293 touch sensor. I'm using SDK 15.3 and started off from the twi_sensor peripheral example...
Hello,
I am using the nRF 52840 DK board. Using nRF5_SDK_17.0.2 I am trying to implement basic BLE advertising in my code. Also, I have turned on the RTT log. From the log...
Hi,
In the SDK 17.1.0 release note (downloaded from https://www.nordicsemi.com/Products/Development-software/nRF5-SDK/Download?lang=en#infotabs ), the verification GCC compiler...
I'm trying to create a Zephyr Shell command where I can write a certificate to the modem. Putting the certificate in the command line doesn't work, so I was going to use the...
Hi
I'm using nRF52805 to realize the DFU function using the buttonless_dfu example project. I follow the instruction of this and use commands in this discussion .
After...
Hi I have an question about use ZB_ZCL_DECLARE_POWER_CONFIG_ATTRIB_LIST macro in case when only one battery used.
I'm trying to declare Power Configuration like this
...
Hi. I don't believe this question would be strictly be considered a duplicate. I have seen posts discussing the same issue I'm having, but resolutions don't appear to solve...
In order to use this application in nRF Connect for Desktop, I have just purchased an nRF52-DK. As I'm using macOS, I believe that I'm affected by the 64 byte limit and need...
Hi,
I am trying to interface WM8960 CODEC with nRF52832 using (I2S and I2C) .
Problem I am having is with TWI scanner and also sending data to the know i2c address . have...
SES 5.44
nRF52840-DK
GNU Arm Embedded Toolchain: 9 2020-q2-update from here
S140: 7.2.0
Project is C code only
Project Setup:
Linker Script File (copy from...
Hello,
I am a research assistant at the Norwegian University of Science and Technology. We have in the past been using the micro:bit v1 for our practical labs which purpose...
Hi, When I hook the nRF5340-DK board to my PC, the SEGGER J-Link OB debug chip bothers me popping up a GUI that exposes the board as a USB mass storage device. How to get...
I'm using Android DFU library 1.11.1 and occasionally I see "E/DfuBaseService: Connection state change error: 133 newState: 0" errors. It appears they happen when the initial...
When using nRF Connect SDK v1.6.1, a BLE peripheral that supports 2 simultaneous connections could be created by including these lines in prj.conf. These lines set the Link...
