Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi team,
My customer is using DTM for the test and they want to know how to change PHY and radio channel setting for the DTM, could you please help to clarify?
Thanks...
in sample ,prj.conf had configure ble device name using below define :
CONFIG_BT_DEVICE_NAME="Nordic_UART_Service" ,
in hci_core.c function bt_enable() use set_bt_name...
Hi Nordic,
In this question: https://devzone.nordicsemi.com/f/nordic-q-a/56529/how-to-check-or-read-the-list-of-bonded-device-from-nrf52832 It was discussed to update...
Is it possible to use both Zigbee & BLE MESH at same time?
Actually we are planning to use NRF52840 for our next project. In which BLE MESH will be used for BLE mesh device...
Hello,
I am using NCS v1.5.0 and my application runs in non-secure mode, and uses a custom SPM. Initially all build and ran correctly, and the SPM fit in a 32 KB partition...
Hi Dev team,
I am running an application using Thingy91 along with MQTT.
I am having a simple logic of storing data for a while and then sending it out through MQTT. For...
Hello,
I've been testing 802.15.4 single PHY (no softdevice) and analyzing packets on a TI CC2531, just to check interoperability. Things seem to work well when the packet...
Hello Everyone.
I am a newbie in NRF52840 development. I have one NRF52840 device as a central device and many peripherals are getting connected to it (Max 6). Lets say...
I am currently using the 17.0.2 SDK to develop some code on the nrf52832 which involves streaming data via SPI to an external flash. I need to stream this data at a ~50KHz...
hello, I have a question need you help.
SDK:nRF5_SDK_14.2.0
MCU:nRF52810
My product is used as a central.
When the voltage of the battery supplying the product is...
I am trying to develop an application using ANT on the 52805, I have purchased the nRF52 DK as this was the recommended development kit for this device but there seems no...
I have a design that uses the NRF52810 as well as NRF9160.
For safety reasons, it must have a fuse that is about 1 ohm into the system. I'm seeing an issue after an input...
Hi, Nordic.
Our customer employs nRF51802 in their product.
They use BLE and 2.4GHz proprietary at the same time. They want to know the switch speed between the two protocol...
