I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am trying to flash one external module which is actually a BLE having (NRF52832 ) and I am using NRF52832 Development board . By doing all the necessary connections...
Hi,
I'd like to evaluate dual mic recording on three 5340 audio DKs: two of them work as CIS headsets(Unicast server?) and the other one as CIS gateway (Unicast client?...
Using Visual Studio Code as IDE with installed nrf SDK v2.9.0 on MacOS Sequoia 15.2
Terminal reads -
* Executing task: nRF Connect: Build: blinky/blinky (active) ...
I am porting my code from Nordic SDK16 to Zephyr and NRF Connect SDK 2.0. I am working on putting a chip into sleep mode and set up a wake up on a press of the button. Everything...
Hello,
I am working through the Zephyr training modules (These are great, thanks!) and encountered an issue I do not know how to resolve. This issue applies to general debugging...
I'm using SDK17.0.2
I need to keep a noinit variable in memory so that I have the correct flag when I execute the DFU. So I use the following method, but it doesn't seem...
I am on nRF52840, and ANCS can get the app name. After switching to nRF52832, you cannot get the app name. The driver of the two chip ANCS is the same, but the Bluetooth protocol...
Hello,
NRF SDK version 2.6.2, tested on 2.8.0 as well
Hardware: NRF7002DK
Sample: Wi-Fi Monitor
When changing Wi-Fi channel using following function
ret = net_mgmt...
We have developed a custom board with an external 32 MHz Crystal but I am having trouble initializing everything correctly. With the Zephyr "Hello World" example code I can...
I want to do BLE FOTA with my customborad, so I have added some configs of FOTA to my developping project.
those configs are referenced ”DevAcademy” Exercise 3 - FOTA over...
I been trying to figure this out but to no avail. I get these errors on build.
:/ncs/toolchains/b620d30767/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi...
Using the "launcher" the open button appears to do nothing and the update from V4.2.0 to V4.2.1 produces an error message.
Twice I have uninstalled V5.1.0 and replaced it...
I'm using an nfr52840 board.
I noticed that when using The 'zephry-sdk' v3.5.99-ncs1-1, when doing a passive scan using:
BT_LE_SCAN_ PASSIVE
which sets:
BT_LE_SCAN_PARAM...
