Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi,
I'm trying to store the DFU image in external flash. I already have DFU on the internal flash working.
When I enable support for the external flash and perform a...
I am developing a .NET C# project that receives data from the Nordic nFR52840 BLE Dongle via BluetoothLE, does Nordic provide any specific libraries for this purpose, or if...
I am migrating from the 2.6.1 development environment to 2.9.0 but am unable to compile due to some configuration issues.
My prj.conf configuration file is as follows: ...
Hello,
I'm reading about 700 values from an LSM6SDO gyro/accelerometers per second and need to store them, before sending them over bluetooth once where I store them is...
I’ve been working on creating a C++ application based on the NUS example, but I’m encountering an error. I’ve attached my application below. All I did was enable CONFIG_CPLUSPLUS...
ncs_add_partition_manager_config does not appear to be working. I am using ncs 2.1.0 and doing a build with MCUboot. Am I doing something wrong below?
I am using the following...
I open up a flash shared space in app and bootloader, write values from app, bootloader read, bootloader read values such as 0xFFFFF, and not ideal values, may I ask why this...
Hi, I'm upgrading the ncs version of my project from v2.7.0 to v2.8.0 and I'm no longer able to compile the project due to a linker error because the websocket_connect function...
Hi,
I followed the instruction ( https://docs.nordicsemi.com/bundle/ncs-2.5.0/page/nrf/samples/cellular/lwm2m_client/sample_description.html ) to build and run on my nRF9160DK...
Here it is suggested to gracefully terminate a thread by sending it a notification of any kind. But how can I terminate a thread that is in a waiting state with K_FOREVER...
Hi,
I cleared my desktop and development environment.
So I rebuilt IDE using VSCode and NCS 2.9.0.
Everything works well without Intellisense in VSCode.
As above...
Hi,
We are using nrf52840, with SDK 16.0. we wanted to know that How does Garbage collection works?!
Does it reuse the allocated pages by erasing it or it uses the new...
I am just starting out. Trying to figure out how to interact with the board and my tool chain. I'm not sure how to flash a merged.hex file I made (serial_lte_modem) into the...
Hi,
I am using the nRF54L15-DK board and would like to use the driver code for the peripheral(Timer,SPI etc).The SDK I am using is NCSv2.9.0,Please help me find the driver...
Hi everyone, Is there a demo or project code showing BLE transfer between two Nordic chips/devkits with a data rate more than 2mbps using 4mbps phy? Thanks.
