Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi
We have a third party that develops some of our products, and this third party does not release their source code. However, we would like to sign our binaries with a...
Hi,
Platform: nRF54L15, SDK 2.9
The application is Matter + BLE. CONFIG_CHIP_DFU_OVER_BT_SMP & MCUBoot are part of the configuration. As soon as we enable the BLE...
I have problems with nRF Connect(Android, latest Version, no version number found) to find BLE devices with 2M phy, coded phy and extended advertising. So i am running nRF...
I have made my own NRF52832 Dev board as in the next image:
I received the board, and ICs and hand-soldered them in my home.
however, I am still a newbie in nRF SDK...
Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
I'm currently developing a BLE Long Range application based on Zephyr and the v2.8.0 version of the nRF Connect SDK. The app is based on the following nRF samples: central_hr_coded...
Hello,
I am currently stuck trying to migrate a project to the 2.8.0 version of the NC SDK.
I followed the exercice of the Nordic Academy : FOTA over BLE .
It works...
I want to automatically reconnect to my peripheral (nrf5340 DK) from my central (phone) when there is an accidental disconnect (out of range) which I am simulating by resetting...
We are using the nrf9160 with SLM V2.4.2 and Modem V1.3.6 and we can do 6 calls to the Verizon cell network in 3 minutes and 30 seconds apart with no issues.
However, on...
I am developing a BLE application on the nRF52 platform using FreeRTOS. My application involves custom BLE services and characteristics, and I am encountering a hard fault...
Hi there,
I was following the tutorial here https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise...
I have a device with 3 major components:
Fanstel nrf52840
PMIC1300
spi display (Waveshare 2.13inch E-Ink Display)
PMIC:
BUCK1: power Fanstel
BUCK2: power...
I am running a modified GNSS demo code for our board. At initialization, there is some traffic going between the MCU and the GNSS chip, but when the demo code calls nrf_modem_at_printf...
I am having a problem after installing 2.9 where I am getting a problem on some projects where the nRF addin does not seem to work
When try to create a new application...
