I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Working to comply with EN 300 328 V2.2.2 by reducing Media Utilisation to <10% on my FHSS system. I've been told that over-the-air, the NRF24L01+ actually transmits 9 bits...
I'm trying to get the settings api working with multiple partitions using little FS. Some of the implementation is specific to Nordic and was hoping to get an example of how...
We have developed a custom board with an external SPI flash, which I have tested and it works.
We want to use OTA over BLE, so we have added MCUboot to the project, which...
Hi all,
I am trying to decide what DK I should go for if I want to test out the BLE Direction Finding capabilities of the SoC.
I am interested in getting the nRF5340-DK...
I'm using an nRF52832 with SDK v15.3.0 configured as an SPI slave in mode 0, with a master clock speed of 1.25 Mbps. My SPI pin assignments are:
- CS -> P0.06 - MISO ->...
I built an application and tested it with DK, and it worked well. I then created a custom PCB and attempted to flash the application, but the BLE part is failing with the...
Hello,
Platform: nRF54L15, SDK 2.9, VS Code
Our application is Matter + BLE (like NUS) based door lock application. A BLE custom service (adapted from NUS) is used to...
Hello,
I am currently learning Zephyr via the Developer Academy in preparation for an upcoming project that will use an nRF9151 and a Nordic BLE module. I will need to write...
Hi!
First of all, sorry but I will not be able to provide anything to re-create the bug... I did modify the code that may have made it happen in the first place quite a...
Hi, my two nRF52840 devices are set as peripheral and central respectively. Both devices use nRF52 SDK.
I try to update the PHY in the two devices, after they are connected...
Hi,
I was playing with my development software in VS Code everything was OK apart from the Cmake error message.
Once I had to restart my computer I couldn't build my...
Hello team,
We are developing a custom board on which eSIM is used for cellular connection. We will use Serial LTE modem application to control cellular modem through...
Hi,
I am using the nRF5340 Audio DK board with the nRF5340 Audio application under NCS v2.8.0 as a Unicast client.
I observed that changing the connection interval to...
