Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I am trying to flash one external module which is actually a BLE having (NRF52832 ) and I am using NRF52832 Development board . By doing all the necessary connections...
Hi,
I'd like to evaluate dual mic recording on three 5340 audio DKs: two of them work as CIS headsets(Unicast server?) and the other one as CIS gateway (Unicast client?...
Using Visual Studio Code as IDE with installed nrf SDK v2.9.0 on MacOS Sequoia 15.2
Terminal reads -
* Executing task: nRF Connect: Build: blinky/blinky (active) ...
I am porting my code from Nordic SDK16 to Zephyr and NRF Connect SDK 2.0. I am working on putting a chip into sleep mode and set up a wake up on a press of the button. Everything...
Hello,
I am working through the Zephyr training modules (These are great, thanks!) and encountered an issue I do not know how to resolve. This issue applies to general debugging...
I'm using SDK17.0.2
I need to keep a noinit variable in memory so that I have the correct flag when I execute the DFU. So I use the following method, but it doesn't seem...
I am on nRF52840, and ANCS can get the app name. After switching to nRF52832, you cannot get the app name. The driver of the two chip ANCS is the same, but the Bluetooth protocol...
Hello,
NRF SDK version 2.6.2, tested on 2.8.0 as well
Hardware: NRF7002DK
Sample: Wi-Fi Monitor
When changing Wi-Fi channel using following function
ret = net_mgmt...
We have developed a custom board with an external 32 MHz Crystal but I am having trouble initializing everything correctly. With the Zephyr "Hello World" example code I can...
I want to do BLE FOTA with my customborad, so I have added some configs of FOTA to my developping project.
those configs are referenced ”DevAcademy” Exercise 3 - FOTA over...
I been trying to figure this out but to no avail. I get these errors on build.
:/ncs/toolchains/b620d30767/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi...
Using the "launcher" the open button appears to do nothing and the update from V4.2.0 to V4.2.1 produces an error message.
Twice I have uninstalled V5.1.0 and replaced it...
I'm using an nfr52840 board.
I noticed that when using The 'zephry-sdk' v3.5.99-ncs1-1, when doing a passive scan using:
BT_LE_SCAN_ PASSIVE
which sets:
BT_LE_SCAN_PARAM...
