Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
I'm currently developing a BLE Long Range application based on Zephyr and the v2.8.0 version of the nRF Connect SDK. The app is based on the following nRF samples: central_hr_coded...
Hello,
I am currently stuck trying to migrate a project to the 2.8.0 version of the NC SDK.
I followed the exercice of the Nordic Academy : FOTA over BLE .
It works...
I want to automatically reconnect to my peripheral (nrf5340 DK) from my central (phone) when there is an accidental disconnect (out of range) which I am simulating by resetting...
We are using the nrf9160 with SLM V2.4.2 and Modem V1.3.6 and we can do 6 calls to the Verizon cell network in 3 minutes and 30 seconds apart with no issues.
However, on...
I am developing a BLE application on the nRF52 platform using FreeRTOS. My application involves custom BLE services and characteristics, and I am encountering a hard fault...
Hi there,
I was following the tutorial here https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise...
I have a device with 3 major components:
Fanstel nrf52840
PMIC1300
spi display (Waveshare 2.13inch E-Ink Display)
PMIC:
BUCK1: power Fanstel
BUCK2: power...
I am running a modified GNSS demo code for our board. At initialization, there is some traffic going between the MCU and the GNSS chip, but when the demo code calls nrf_modem_at_printf...
I am having a problem after installing 2.9 where I am getting a problem on some projects where the nRF addin does not seem to work
When try to create a new application...
Hi, On Ubuntu, after a distribution upgrade from 22 to 24, NRFConnect has failed in a couple of ways. 1. Upon starting, the application fails with: [7982:0910/180010.628514...
I am facing error while building the sample "Hello World for multiple board targets using Sysbuild" without changing anything in the sample. I am using nRF connect SDK and...
I am using the nrf52840 USB dongle, I flashed it with the OpenThread CLI and I managed to locate my PAN ID, Master Key and Channel from the separate thread/matter dongle for...
Hi,
My custom boards with nRF9151 don't get gps fix. I'm using the same GPS antenna and LNA as DK. Soft is from DevAcademi example, but tried also GGSN sample and some other...
