I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello,
We have a design that includes both the nRF52840 and the nRF9160. We are doing custom antenna designs in a miniaturized form factor and would like to specify required...
Hi
We are verifying the encrypt value and MIC value using a crypto tool.
The result is different depending on the setting of the packet S0 field.
If the S0 field is...
Hi,
I use this code for sampling analog input with 3.3 kHz and send it over BLE to PC , i use dongle to to read the sampled datas on nrfconnect tool for desktop. I tried...
Hi,
When connecting my Nrf52840 to a PC using BLE nfc, after connection is established, I encountered the following error : BLE_GAP_SEC_STATUS_OOB_NOT_AVAILABLE – Out of...
I have following the getting started tutorial and install everything mentioned in the documentation.
But the button "Flash" or "Erase and Flash" in VS Code are not working...
The NRF documentation for nrf_pwm_sequence_t says:
When the sequence is set (by a call to nrf_pwm_sequence_set), the provided duty cycle values are not copied. The values...
Hi,
We have implemented FOTA on an nRF52dk (nRF52832) using nRF Connect SDK v1.8.0. That works fine. Now we have encountered a problem that we believe is due to a limitation...
I need to create an IoT QR code reader.
I decide to use the NRF9160 board because it integrates a lot of components that I need to use (LTE, GPS, Bluetooth) so the only...
Hi,
i use event_manager with few modules.
One module use Sensor LIS2DH driver that read data via i2c data when triggered and send it to other module as event.
Second...
Hi,
I'm using nRF52805.
The main power is 3.3V LDO output.
When main power is out, the battery(3V, Coin battery) should be a power source of nRF52805.
But, when battery...
Hi,
I've just returned to working on an nRF52811-based project after a year so I'm a little rusty, and I'm wondering if it is necessary to explicitly call SystemInit() ...
Hello,
I'm experimenting with nRF Connect SDK 1.9.1 and I want to use SAADC, however I'm running into the following error message.
Please note that the code compiles....
I planned to use THE UARTE of nRF52840, but I encountered some problems when I added it to the project from the routine of SDK17.0.2. I compared the UARTE and sdk_config.h...
Hi,
I would like to help/influence the course of our on-going project with nRF52832 such that the recommended/default Toolchains are used. In this regard I have the following...
