Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello everybody,
My project is based ble_app_eddystone example and nRF5_SDK_17.2.0 SOC is nRF52832.
Beacon advertise Eddystone UID +Eddystone TLM +Eddystone URL, works...
Dear,
how to change the adv. timeout setting and disable uart0 and uart1 in ncs v1.6.1?
I use the nRF5340 and example peripheral_lbs.
The path is as below:
nrf\samples...
I am using the following CAF modules on nRF52840DK, ncs 1.9.1: Buttons, LEDs and Power manager (see attached project caf.zip)
Button 1 is used for ON/OFF fuctionality. When...
I submitted a project idea for the Electromaker make it smart thingy:91 contest. Part of that was to detect and alert a user if there was an impact. This would require access...
How do I find out which peripherals are available at the same time?
Somewhere it was mentioned, that peripherals wit the same "ID" are on the same HW and only one of them...
Hi,
What's the max range achieved with BL5340 (With PCB Trace antenna) in indoors and Outdoors when advertising and connected mode? (With 1M,2M and Coded PHY(125Kbps,...
I use nrf connect sdk 1.9.0, to run periodic_adv and periodic_sync example.
The adv side sends this data: mfg_data[] = { 0xff, 0xff, 0x00 };
But in sync side in scan_recv...
Hi,
My mesh project is occasionally suffering some dropped messages and after probing around I found this on one of the nodes.
I have four nodes and one gateway running...
Hi,
In nrf52840 dongle, I use nrf_crypto_ecdsa_sign function to sign.
Everything is fine in when building, but when testing the real world data, it’ll will show error...
I use 52820 to do ble_usb+esb project, but I have encountered problems when adding USB. I have added USBD_HID_COMPOSIT in the project of \ examples \ peripheral \ usbd_ble_uart...
Dear community
I am developing an autarkic embedded system where I harvest energy from a thermoelectrical generator. It is a simple application, I need to acquire the open...
Hello,
NCS1.8.0 Windows10 X64;
i test v1.8.0\nrf\samples\bluetooth\direct_test_mode, and i want to use nrf21540 model.
i've set CONFIG_NRF21540_FEM=y and do Project...
Hi,
I have been playing around with the nRF9160 DK trying to get it reading a range of sensors, so far with success, however I have found an issue which has stumped me...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We connect to the broker through the MQTT command...
