hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
Kicked off an application FOTA update, and somehow it failed:
[00:02:06.161,315] <err> download_client: Error in recv(),...
I've built a firmware based on the hci_uart sample with the softdevice controller. The board is custom made and has a nrf52840 on it. Over USB-CDC HCI commands are sent to...
Is there any issue with using the nRF52833 DK/nRF52833 for Matter development? I’m asking because the Matter template doesn’t seem to support the nRF52833 DK/nRF52833. If...
Dear Nordic People Recently I am following YouTube link from Nordic Semiconductor for Implementing ESL https://www.youtube.com/watch?v=VeLkptpSvRQ This video requires specific...
Hello and thanks for reading. Also happy holidays.
We are using an NRF5340, and are having some issues with connectivity. I would therefore welcome any suggestions you may...
Hello
I've been experimenting in increasing the number of targets that a mesh FOTA distribution server can support on nRF52840
The CONFIG_BT_MESH_DFD_SRV_TARGETS_MAX has...
We want to upgrade our existing product to WiFi 6. We have a lot of customization in our TCP/IP stack so we don't want to use the zephyr stack. We only want to make the station...
While in the field test phase of our custom nrf9161 based device, we figured out that there are some towers of some providers that make the device seem online although it...
Hello,
I need to use the Radio_test example on a custom board using the nrf52810. I am using the nrf connect SDK 2.5.1 with VSCode.
To use the Radio_Test example I need...
Mesh 1.1 Generic Location Server defines special values for long/lat and north/east when unconfigured. Current code doesn't appear to support/use these special values, instead...
Hello everyone,
I am developing a ble project that builds on the peripheral Uart example using the sdk 2.4.0 for nrf5340.
I want to implement a watchdog since I sometimes...
Howdy!
I am working with the nRF52840 and currently getting a weird error. Whenever I set the data for the BT_DATA function as anything greater than 110, the system stops...
Hi, I'm using the power profiler II under Manajo with JLink_Linux_V794i_x86_64. I connected my power profiler to measure power consumption, the app (nrfconnect-5.1.0) ask...
I'm trying to use the new GRTC peripheral in nRF54L15 but in various situations I notice that the events are not triggered as expected.
Here is a "minimal reproducible example...
I created project from blank, and added a build configuration. Now it showing as 1 configuration | 2 contexts, as shown in the screenshot below:
What are these contexts...
