I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
I'm running SDK 2.8 and 2.8 Toolchain. I created the sysbuild.conf setting:
SB_CONFIG_BOOTLOADER_MCUBOOT=y
and put it in the application folder (per this support request...
Hello, I am relatively new to the nRF 5340 Audio DK. I recently ordered a singular nRF 5340 Audio DK board and my goal was for the board to take in input audio via the PDM...
Hi all,
I've been using the nRFConnect extension without any issues, successfully connecting to my nRF5340 board via JLink, flashing firmware, and receiving printed messages...
i get the following build error whenever i build for boards other than nrf
- CMake version: 3.21.0 -- Found Python3: C:/ncs/toolchains/b620d30767/opt/bin/python.exe (found...
Hello,
I encountered a compilation issue when using the app_timer function. The error message is: "'TickType_t' undeclared (first use in this function)". I believe the problem...
Hi,
I am trying to set the VDD pin to 3.0V instead of the current 1.8V (also changing the GPIO voltages to 3V). I've seen many questions related to that but no solution...
Hi Support Team
May we know that the difference between Engineering Build Code BB0 of nRF54L15 with normal Build Code? Which is recommended for the mass production of customer...
Hi, I am using nrf9151-DK to send and receive data over UDP protocol. Firstly, I tried to use AT commands to send and receive meassages as described here , I had no isuues...
Hi,
How can I control a Thread CoAP Client, which is connected to a thread supporting modem such as eero+ (in other words, the CoAP client is connected to the internet)...
Hello
I am trying to build the Zephyr mesh distributor sample on the nRF 52840 dongle
It builds and runs just find on the nRF52840 DK
But when I try to build for the...
Hello,
I'm looking at adding USB DFU to my project, (Not USB DFU recovery in the bootloader, but in runtime) and was trying this example. It fails to build for the nordic...
Hi,
im develop a keyboard by ncs sdk in nrf52840,and one funcation is that power off/on the keyboard ny fn key .i see the CAF: Power manager module , It doesn't seem to...
Hello, I've been developing on a Nrf5340 board and I am trying to gather pressure sensor data from both a adafruit mprls pressure sensor breakout board on i2c and then a Honeywell...
I've been tasked with studying adding Auracast to an application. One fundamental thing I can't get my head around is what is the s/w requirement - i.e. do I need 3rd party...
