An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I am trying to get mcuboot working on a custom board. on version 2.7.0 sdk, But the board is not found.
I have simplified it to a minimal version like so (my folder can...
I am evaluating external flash on nRF5340DK. When I'm doing appcore DFU from external flash so that mcuboot_secondary and settings_storage are located on external flash, everything...
Hello!
I am returning to software development for a BLE Mesh project on the NRF52840 after being focused on the hardware development for several months. I see that NCS is...
Hello
I am evaluating Wi-Fi location using the nRF7000 and nRF9160.
For the initial test, I used the nRF7002 Expansion Board. I soldered wires to it and connected them...
What would be the certification cost for developing small volume Zigbee or Matter+Thread applications using nRF modules and nRF Connect SDK? Is this eligible to certify via...
Hi experts,
I followed the instructions the Readme file described. It almost works well. But I still found two issues:
the Startup time is too long when pressing the...
Hello!
I am currently using the nRF7002DK, and I am interested in utilizing the nRF5340 MCU as a slave SPI with an external MCU that supports 3.3V SPI voltage levels. My...
hi
board : nrf52840 custom board
sdk : nrf connect sdk v2.6.1
example: matter light bulb
problem:
After the code is burned in, the system not working, I have modified...
Hi, I create a customboard on NRF54L15. After that, I create a new application => Copy a sample => Blinky. I just build without fix anything code, but it isn't build completely...
Hi, I am working on long press button interrupt in nrf52832 device & used NCS. I am unable to detect the long press from button.below is my functionality which is I am trying...
Hi,
I am trying to flash one external module which is actually a BLE having (NRF52832 ) and I am using NRF52832 Development board . By doing all the necessary connections...
Hi,
I'd like to evaluate dual mic recording on three 5340 audio DKs: two of them work as CIS headsets(Unicast server?) and the other one as CIS gateway (Unicast client?...
Using Visual Studio Code as IDE with installed nrf SDK v2.9.0 on MacOS Sequoia 15.2
Terminal reads -
* Executing task: nRF Connect: Build: blinky/blinky (active) ...
I am porting my code from Nordic SDK16 to Zephyr and NRF Connect SDK 2.0. I am working on putting a chip into sleep mode and set up a wake up on a press of the button. Everything...
Hello,
I am working through the Zephyr training modules (These are great, thanks!) and encountered an issue I do not know how to resolve. This issue applies to general debugging...
