At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message when something hits the device. To achieve this...
Hello All,
I am using the nRF54L15-DK and the nRF Connect SDK v2.8.0 with the Zigbee-Addon.
Is the maximum TxPower value that can be set for Zigbee 8 dBm?
Best regards...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. I am checking the operation of "Scheduler Server". The action was executed, and the date and time are...
Hello. Using the Zigbee messaging cluster, we are writing code for data exchange between ZR and ZED. (Based on the Zigbee example light_bulb/light_switch/light_coordinator...
Hello,
I have a custom board which has an nrf5340 on it. We are using nRF Connect/Zephyr in this project. Currently the board has a pretty simple interface seen in my overlay...
I am currently developing a PC application for Bluetooth data reception and chart display. I want to perform secondary development on pc-nrfconnect-ble. My current development...
I'm using SDK15.3 on an nRF52840 with FreeRTOS and specifically non-preemptive scheduling.
I want to so some transfers on SPIM (it's configure with DMA but that's not a...
My project uses a PDM microphone connected to a nrf5340. I previousy had this working using the nrfx_pdm driver, with NCS 2.6 but then had to migrate the project to NCS 2...
There is usually a panel for application where you can see / delete or add build configurations, as shown in the enclosed picture. The panel on my vs code installation has...
Hello,
i am debugging issue in our device. I ported the nrf5340 Audio application to our custom board and modified it for our use. We use audio broadcast mode.
Device...
HI,
I am developing a ble mesh application on SDK 17.2, I enable Instaburst for support long mesh message(more than 300 byte), it worked well.
Now I changed to the nRF...
Dear Support Team,
I'm trying to develop a mouse using Pixart's PAW3395 sensor. I've written functions for reading and writing data through the SPI interface. I took help...
I didnt see in the data sheet a specific window of time the chip needs to properly shutdown without interrupting a critical process that might cause corrupted memory. I am...
Dear Nordic Engineers
I would like to test the GPS of NRF9160 with CMW500.
I used a line(IPEX to SME) to connect the GPS pedestal to CMW500.
I downloaded the serial...
