This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I have made my own NRF52832 Dev board as in the next image:
I received the board, and ICs and hand-soldered them in my home.
however, I am still a newbie in nRF SDK...
Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
I'm currently developing a BLE Long Range application based on Zephyr and the v2.8.0 version of the nRF Connect SDK. The app is based on the following nRF samples: central_hr_coded...
Hello,
I am currently stuck trying to migrate a project to the 2.8.0 version of the NC SDK.
I followed the exercice of the Nordic Academy : FOTA over BLE .
It works...
I want to automatically reconnect to my peripheral (nrf5340 DK) from my central (phone) when there is an accidental disconnect (out of range) which I am simulating by resetting...
We are using the nrf9160 with SLM V2.4.2 and Modem V1.3.6 and we can do 6 calls to the Verizon cell network in 3 minutes and 30 seconds apart with no issues.
However, on...
I am developing a BLE application on the nRF52 platform using FreeRTOS. My application involves custom BLE services and characteristics, and I am encountering a hard fault...
Hi there,
I was following the tutorial here https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise...
I have a device with 3 major components:
Fanstel nrf52840
PMIC1300
spi display (Waveshare 2.13inch E-Ink Display)
PMIC:
BUCK1: power Fanstel
BUCK2: power...
I am running a modified GNSS demo code for our board. At initialization, there is some traffic going between the MCU and the GNSS chip, but when the demo code calls nrf_modem_at_printf...
I am having a problem after installing 2.9 where I am getting a problem on some projects where the nRF addin does not seem to work
When try to create a new application...
Hi, On Ubuntu, after a distribution upgrade from 22 to 24, NRFConnect has failed in a couple of ways. 1. Upon starting, the application fails with: [7982:0910/180010.628514...
I am facing error while building the sample "Hello World for multiple board targets using Sysbuild" without changing anything in the sample. I am using nRF connect SDK and...
I am using the nrf52840 USB dongle, I flashed it with the OpenThread CLI and I managed to locate my PAN ID, Master Key and Channel from the separate thread/matter dongle for...
