Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
I am writing some code for a customer using the nrf52840.
The Softdevice asserts immediately after a call to nrf_fstorage_write().
The write address is OK, alignment...
whenever I use nrf connect desktop app in my Linux system for power profilling.
The power profiling kit doesn't start and keeps on giving the same error
There are similar...
Hello team, I'm working on system development using Mesh SDK and I have some questions so please let me know. ############### Development environment IDE : Segger Embedded...
I was able to create 2 times, Timer 1 and Timer 2.
They work when they run separately, but one stops when I try to use both of them.
I need simultaneously running two...
Please confirm the following is correct for nRF52840 (per PS v1.1)
1. The firmware doesn't have to enable internal pull-up when the pin reset is configured (it's done automatically...
Hi,
I am developing a solution with zigbee (nRF52840).
I want some end device is joined to specific router.
In the documents, if end device find more than one router...
Hi, Everyone.
I'm trying to connect nRF52 DK Board to J-link base tool.
But I can't connect.
Wires between nRF52 B/D and J-link base tool are conneted below.
nRF52...
Hi,
I am new in this area. I wanted to use the detect "signal" but it doesn't work as protected. This is my main :
I just try to detect when the detect signal is HIGH...
Hello,
i tried the getting started procedure with the NRF9160DK demo board but I cannot finish the whole procedure.
After activating the iBasis eSIM, I turn on the...
It's may be strange enough, but i can't see the clear answer on this question. What is the limitations for pin function maping? I need to understand which pins i can use for...
Hi,
I am surveying the zigbee example for my project.
In my project, coordinator has to permit or reject certain end device/router.
I have searched following articles...
Hi,
We want to send our board for Radio testing and the facility needs a test setup. Radio test example could work perfectly for us but unfortunately, I am unable to use...
Does Nordic Thingy come with on board SEGGER J-Link programmer / debugger like the nRF52832 DK?
If not then how to program and debug development firmware on Nordic Thingy...
Heloo, I'm using NRF 51 DK and NRF 51 822 QFAA__ mcu.
Flashing the DK is fine, all of the examples are compiling and running as expected, also the modifications introduced...
Have previously used the QFAB. Are there any settings in the compiler or debugger that need to be different ? - my understanding is that xxAB refers to both.
Understand...
