SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
I am currently working with the nRF52 DK and have compiled some code to read ADC values. This code works fine with the nRF52 DK but I am having trouble getting it to work...
Hello everyone, I'm developing a wearable device based on nRF52832 which reads IMU (ICM20948) data using TWI.
The problem is that if I try to use the code with a custom...
hello everyone,
in my project i need to advertise the sensor data as well as connecting the BLE TAG . in detail i am using nrf52810 with mpu6050 and i want read the accelerometer...
Hello,
During my evaluation of nRF52840 I discovered an issue which prevents the device from joining a Zigbee network successfully.
I'm using out of the box zigbee/light_bulb...
Hi,
I've installed all by the book watching the installation videos and I have a problem building in VScode
when I try to build with nrf connect app window I get this...
Hello,
To preface, this project was redirected to me and I have very little experience using SoCs. Happy to provide any additional information and apologies for issues in...
Hi!,
I am trying to create an application with BT Mesh using the nrF52840 DK and two nrF52840 Dongles with an OnOff Model Server and an OnOff Model Client respectively....
Hello.
I am new to Zephyr, I know how to digital read the pin which is used as INPUT
#define SW0_NODE DT_ALIAS (sw0)
static const struct gpio_dt_spec DOUTINPUT = GPIO_DT_SPEC_GET_OR...
Greetings,
I'm using NRF52840 with softdevice and nRF5_SDK_17.1.0 on NRF52 DK.
The shutdown_handler in my code is as follows:
There is a secure bootloader from Nordic...
Hi, I am using nRF52832 module as connectivity chip (GAP peripheral, GATT server) with ble_app_uart_pca10040_s112 as source.
I am using nRF connect app to test data communication...
I am currently developing a feature for a BLE module to pass certifications (BL654 Laird, based on nRF52840). My application runs on SDK 15.0.0. I used the "radio_test" module...
My overall goal is to update the percentage of battery left in the advertiser and then either go to a nine second sleep to conserve as much power as possible and then wake...
I am following the instructions to enable micro-ecc support for an example code ( secure bootloader ble s132 pca10040 debug). I am using SDK 17.0.2.
I have successfully...
I'm sorry, maybe it's me, but your SAADC documentation leaves much to be desired, as I was easily able to implement getting readings from a single analog input (non-blocking...
Hi,
Trying to do a very simple thing.
I want to start a new project from a sample project, but I want my new project to be in a different folder
Load nRF Connect...
