Good morning!
I hope you will forgive my trivial question but I am a beginner. I don't quite understand the partition structure presented in the "NVS" example. Using the...
Issue:
Using the stock nrf_dm example project, there seems to be no way to disable GPIO debugging and serial drivers at the same time. You get the following build error...
Hi, Im working in nrf9160dk, I'm referring aws iot document there they given a code 6278.aws_iot_tutorial.rar there im getting this error .what i need to do?
Executing task...
Hi,
I'm currently trying to add DFU OTA in my project.
I had add few lines for enable bootloader and BT OTA to my proj.conf, but keep getting error when building the project...
I have an issue that I don't know how to debug. I take the latest version of Zigbee Light Bulb example code and the only change I make is add CONFIG_ZIGBEE_CHANNEL_SELECTION_MODE_MULTI...
Hi, all. I'm using PPK2 in amper meter mode. Version of SW: - nrf connect for desktop application: v.4.4.1; - power profiler: v.4.0.0; - laptop under Linux Mint 20.2 Settings...
1) Is it possible to program and read data in nRF5340 using USB lines?
2) Is the below schematic correct for our requirement do we need to add anything else?
Dear Nordic support team
(This issue is similar to Case ID: 318424)
I would like to test the FOTA functionality using the the LwM2M client sample project.
So far, I...
Hi,
I have two nRF52840-DK with one transmitting and one receiving. I have been trying to calculate the CRC for an ESB packet. However, the CRC reported by the Rx board...
I am trying to use a nRF21540-DK on macOS and I am having some issue with the J-Link thats on board.
The J-Link FW reports as:
Firmware: J-Link OB-nRF5340-NordicSemi...
We are using the nRF9160 with a cellular service provider that has quite a strict firewall policy. There are rejected connections and we suspect a problem with cached DNS...
Hello Nordic engineer,
I use SDK 17.1.0 and s140 for development
【1】 I would like to know how much flash and RAM the S140 softdevice occupies, and if there is a link...
The following snippet is cited from C:\ncs\v2.5.2\zephyr\boards\arm\nrf5340dk_nrf5340\nrf5340_cpuapp_common-pinctrl.dtsi file. It uses NRF_PSEL(fun, port, pin) to set port...
Hello,
I'm currently debugging an issue we are having with MQTT device shadow interaction on the nrf9160. The issue presents when we push a large amount of config JSON to...
Dear Support
We currently use a custom PCB board with RAK4630 (NRF52840 + Semtech SX1262)
We started to try with RAK sample located here
https://github.com/RAKWireless...
I am attempting to work thru the tutorial exactly per the instructions, and I'm stuck in Lesson 1 at
6. Wait for the device to connect to nRF Cloud.
The Cellular Monitor...
Hello,
ncs 2.6.0
device: nrf52840
we are migrating our code to Zephyr and noticed that PSA implementation of AES 128 CTR doesn't support pure streaming mode (or it's...
Problem: Upgrading to newer SDK broke RTT processing of backspace character. Details: We had been using RTT with the v2.4.1 SDK (for our nRF52840 development) and yesterday...
I want too add AES encryption to my project
I've copied the code from aes/samples/crypto/aes_cbc to my project
I've copied the contents of project.conf to my project ...
Hi Supporter
I try to use sample code nrfx_spim (non blocking), how can I specify for SPIM4 high seed?
I use nRF7002-DK with nRF5340
SDK: v2.5.2
#define SPIM_INST_IDX...
Hi Support Team,
I'm using BLE in 'Split Controller and Host' mode on nRF5340 DK. I ported the sample ' peripheral_uart ' for appCore and ' hci_rpmsg ' for netCore, and...