Hi all,
I am new to the nordic controllers and ANT+ protocol.
And I am going to evaluate ANT+ protocol in nrf52dk board (nRF52832 controller).
I need to understand which...
Hi,
I am trying to run the http client on my nrf9160-DK but it is giving me an error below;
*** Booting nRF Connect SDK v2.5.1 *** HTTPS client sample started Bringing...
Hi there,
I'm currently working on the firmware versioning and the downgrade protection for an nRF5340 with NCS 2.6.0.
The firmware consists of:
I currently have...
What is the impact of the power cut off immediately to the chip during boot up or update firmware?
1. Will the power drop immediately to ground?
2. Does the power cut...
Hello,
Is there any way I can enable Read /write protection from Jtag for NRF BC52805M
I am looking for something like (ST RDP protection level 2) where once we flash...
Hi,
I am using SDK 2.3.0. I have recently enabled child supervision in a system with one FTD and many SEDs. I am testing backward compatibility with older FTDs which doesn...
Hi Support Team,
I'm using nRF5340-DK and the netCore was used for the BLE controller only, the appCore was used for the BLE host and my application.
The below cmake arguments...
We're developing an LwM2M application based on the lwm2m client sample with the goal of sending data to ThingsBoard as our main telemetry platform.
The Application in based...
Hello,
We are developing a custom board having nrf9160 cellular modem and we are using serial ltm application in it.
in serial ltm application there is pin selection...
HI,
two years ago I started my adventure with the nRF52840 microcontroller. I started using SEGGER Embedded Studio for ARM as my development IDE. I created a peripheral...
Hi all,
I am new to the nordic controllers and ANT+ protocol.
And I am going to evaluate ANT+ protocol in nrf52dk board (nRF52832 controller).
I need to understand which...
Hi,
Am Implementing Zigbee on NRF52840 chip with help of VS Code.
Zigbee Stack : 2.5.2
I configured nrf52840 DK as Zigbee network coordinator and another custom made...
Hi,
I am trying to run the http client on my nrf9160-DK but it is giving me an error below;
*** Booting nRF Connect SDK v2.5.1 *** HTTPS client sample started Bringing...
Hello everyone,
I'm working on a Zigbee project that has the Thingy:53 as an end node. The program of the Thingy is a variation of the Zigbee Weather Station .
I'm measuring...
Hi,
We're currently working on a project that involves using the NPM1300 to power the NRF52 DK using the GPIO pins. We've managed to supply 3.3V using the GPIO button but...
Hi there,
I'm currently working on the firmware versioning and the downgrade protection for an nRF5340 with NCS 2.6.0.
The firmware consists of:
I currently have...
ble peripheral and central both is nrd52840.softdevice is nrf52.7.2.0. peripheral PHY is 2M ,peripheral send 160K bytes data needs 14 senconds.how to increase the transport...
I am trying to read acceleration values from an acceleration sensor (IIM-42652) via SPI with nrf52832 as the SPI master. I created it based on the spi_pca10040 example,...
Hello!
I'm trying to run an example from the course: Exercise 3 – FOTA over Bluetooth Low Energy . Everything is built without any problems, I use nRF Connect SDK version...
I have the nRF52840 USB dongle, and I want to set up Wirepas by flashing the .hex file. Do I need to set up the nRF5 SDK or Segger EMbedded studio (SES) for this process on...