I'm trying to achieve a 10 ms connection interval using the LE Coded PHY.
SDK version 2.5.0
After implementing support for LE Coded PHY into our central application, I...
Hello! I'm working on some project using Fanstel BM832 module. I'm using the configuration based on board nrf52dk_nrf52832, with some minor modifications (led's and button...
Hello everyone,
I am working on a low consumption product and to optimize it I was using the PPKII to analyze my tuning.
I had strange observations so that I decided...
I have a system I'm working on that requires a complicated device init ordering.
The system has 2 voltage regulators each with an enable. One regulator has the enable tied...
My setup is a nRF7002-EK shield on top of the nRF9160-DK. Trying to use this shield to connect to a Wi-Fi network, using the shell example compiled with the suggested command...
Hello,
I've been trying to get MCUboot to work with Direct XIP for several days but each time I have a compilation problem:
In fact, I would like to have a project...
Hi,I'm develop with the nRF52840 V17.0.2 ,SD 7.2.0
problem about migrate LVGL 8.1
I have few app_timer ,they are work fine
try to migrate LVGL
alfter lv_init(), app_timer...
Hi,
I have a problem when tring to establish wifi connection with complex wifi networks. Here the complex wifi network mean many AP have been confiured the same SSID and...
I'm trying to achieve a 10 ms connection interval using the LE Coded PHY.
SDK version 2.5.0
After implementing support for LE Coded PHY into our central application, I...
Hello! I'm working on some project using Fanstel BM832 module. I'm using the configuration based on board nrf52dk_nrf52832, with some minor modifications (led's and button...
Hello,
I am working on a Mac mini, Apple M2 chipset, macOS Sonoma 14.2.1. I am using Visual Studio Code Version: 1.86.2 (Universal) Commit: 903b1e9d8990623e3d7da1df3d33db3e42d80eda...
using the NRF52832 processor.
The issue we’re having is sometimes the processor won’t start up properly.
We think that it’s because the VDD voltage does not going all...
This not a question. It is for your information (FYI). I've seen many questions about flashing the nRF53 using CMSIS-DAP. Anyone interested see attached instructions.
The...
Hello everyone,
I am working on a low consumption product and to optimize it I was using the PPKII to analyze my tuning.
I had strange observations so that I decided...
Hi Nordic! Using the MQTT from zephyr to send data to my broker. The data is received and the broker sends a PUBACK but the event is not triggered in my event handler. Is...
Hello,
nRF52840
ncs-v2.5.0-rc2
I am using a GPIO interrupt to trigger a callback on every edge on a particular GPIO. I am then timing the difference in time between...
I'm having problem with SPI devices using nRF Connect SDK 2.6 with a 9160DK. Following lesson 5 in the intermediate course I get BUS FAULTS when the application starts.
...
I have a system I'm working on that requires a complicated device init ordering.
The system has 2 voltage regulators each with an enable. One regulator has the enable tied...
Hi there!
I'm using nRF Connect SDK v2.1.2 and VS Code 1.73.1 with nRF Connect extensions on a Windows 11 x64 machine. I created a Freestanding application based on the...
hi professor,
The npm1300 is used for power management on my borad.When VBAT and VBUS are connected simultaneously, the bulk 2 output power supply varies between 1V and...
Good afternoon.
I have asked for help before regarding my nRF52840 Dongle and Ant+ and you have helped me a lot! But I have one more difficulty - I have an error when initializing...
My setup is a nRF7002-EK shield on top of the nRF9160-DK. Trying to use this shield to connect to a Wi-Fi network, using the shell example compiled with the suggested command...