First time here? Check out the Tour!
I have been analyzing the current consumption of my nRF52832 dev kit today using both a multi meter and an oscilloscope with a resistor. I'm not sure what I exactly did that lead to this, but now my board ... (more)
I am using nrf52832 with PCA10036 V1.1.0. Soft device code is s132. I would like to know whether it will support Bluetooth 5.
I have downloaded nrf52 sdk13.0.0.04 version, in that PCA10036 folder was ... (more)
Following this tutorial : https://devzone.nordicsemi.com/tutori...
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
: *** [_build/nrf52840_xxaa.out] Error 2 make: *** [_build/nrf52840_xxaa.out] Error ...
I'd like to create a firmware that supports multiple Nordic boards as Hardware (as the nRFConnect Firmware does). To do that I have to configure the peripherals according to the layout of these boards.
How can the firmware ... (more)
Hello, i think this is simple question, but nowhere i can find answer. Is nRF52840 preview development kit (PCA10056) contains built in nrf52840 microcontroller or i need to buy chip separately?
Thanks in advance, L3s
Hi, I'm new to development using nordic's products. Basically I'm a Hobbyist working on a project of mine, which needs a low cost wireless. I was looking for a Rf Soc and found nRF24LE1 which fits my ... (more)
I try to print the RSSI level but i couldn't do. I use nRF51 DK and soft device S130.
This is the line that i just write:
I don't need to connect the master with the peripherals, but i have to know how is the maximun quantity of scan response that can accept the master. In the example ble_app_multilink_central this is defined like that:
I want to program the BMD-300 with the nRF52 Preview Development Kit. I have connected:
BMD-300 -> nRF52-DK
SWDIO -> SH_SWDIO (pin #4) on P20
SWDCLK -> SH_SWDCLK (pin #5) on P20
VDD -> SH_VTG (pin #3) on P20
GND -> SH_GND_DETECT (pin ... (more)
I want to connect one board trough SPI to my nRF51-DK. Using SDK11 and SD130, the nRF51-DK is the SPI master, I call the function
nrf_drv_spi_transfer() but the CS Pin is never toggled. To solve this I changed it ... (more)
Hello, we have made cars that play laser tag against eachother using infrared emitters and receivers. The problem is that the infrared radiation bounces off the surroundings, and the cars end up getting hit by themselves.
The way it is ... (more)
I am facing a weird issue trying to achieve DFU over the air with the dual-blank DFU. I had integrated DFU with my application(Background story here.) The application hex file, app.hex was merged with s110 softdevice ... (more)
I want to program the ARM MCU in the nRF51822 Development Kit for my own purposes and then send the processed data using the BLE module in the kit to another nRF51822 Development Kit which receives the data and displays it.
I want to purchase a BLE development kit. My current preference is nRF51 because there are more nRF51422 BLE modules in the market. https://www.nordicsemi.com/Products/3...
I would like to run ble_app_uart on the BLE chip. Does ... (more)
I am looking for a nordic BLE development board that can do data transfer through the UART. Something like SPP (Serial Port profile). Here is what I need;
I am trying to use for the first time my nRF51822 development kit, following the "Development Kit User Guide v1.3". The problem is that when I open "nRFgo studio" I cannot see any Board on the "Device ... (more)
I get the following error when trying to build to target: make: * No rule to make target `nrf52832_xxaa'. Stop.
I am doing the following on the Blinky Example program: Makefile->Make Targets->Build->(Target) flash nrf52832_xxaa->Build
I have 2 nRF51 Development kits and a nRF51 dongle that I am using for proof of concepts. I am mainly using the nRF51 IoT SDK because we are looking at using IPv6 with 6LoWPAN. I have a standard Bluetooth ... (more)
I just bought the Nordic Semi nRF51822 DK (without the starter kit). I tested the Heat rate monitor app and it worked fine. It could send some random values to the master control panel. I downloaded the nRF ... (more)
I have a new nRF52 Preview Development Kit, after connect it to a computer with a USB cable, the status light (LD5) come on, indicating it has power. However, the standard USB driver does not appear as described in the ... (more)
In IAR Embedded Workbench for ARM, version 188.8.131.5238 (w/ common components version 184.108.40.20684) with nRF5x MDK for IAR version 8.0.3.
When selecting the target in General options -> Target -> Device = nRF52832_xxAA, IAR cannot ... (more)
Can you please provide full schematic for nRF52 dev board. I looked though the documentation and there are small bits of the schematic, but I didnt find full sch.
Greetings, There is a bit of strange operation in UARTE peripheral in nrf52832 with the DK. In the simple code below, if both of the if statements with comments 'Check 1' and 'Check 2' are removed the 'hello' prints are ... (more)
I've recently bought a nRF905 development kit. From the nDP soft, i cannot detect my nrf905 EVBOARD.
The following driver is installed : "nRF2401 FS USB DEMO" and the board seems to be well recognized by my windows (XP ... (more)
We have been using the nRFgo nRF51822 development kit for prototyping. We now want to design our production board. However, your site says that this dev. kit is not recommended fro new designs. Is there anything about the circuitry on ... (more)
I am using nRF51822 development kit without the motherboard .
I flashed the ble_app_uart (nrf51822/Board/pca10001/s110/experimental/ble_app_uart) and it was successful. but I am not able to discover/ find the device using the nRF Uart App ... (more)
I plan to buy the development kit from Nordic but I had a couple of questions: 1)I know that in a previous question I posted I was told that I can use the development kit to flash ... (more)
I'd like to know, if there is any difference between nRF51822 EK and DK, except device number. Two devices from EK will be enough for me. https://www.nordicsemi.com/eng/Produc... https://www.nordicsemi.com/eng/Produc ... (more)
I've been reading about BLE dev kits lately for one of my projects. I purchased the BLE Mini by RedBear Labs and had a good time with it... till I started writing my own custom firmware. TI ... (more)
I am using the PCA10001 v1.0 from the development kit and am having trouble measuring the same current as the one from the specification. I am using the ble_app_proximity example and measure 25-30uA between advertising peaks whereas around ... (more)