First time here? Check out the Tour!
I am doing current measurements on the nrf52840 in sleep mode with no RAM retention and I am getting different values based on how I take the measurements. Please see the various methods and resulted below.
Using an ...
What is the recommended development tool setup for nRF52 Preview DK on Mac OSX? Your guide for SDK 0.9.1 seem to rely on Keil which isn't natively available for OSX.
I have been analyzing the current consumption of my nRF52832 dev kit today using both a multi meter and an oscilloscope with a resistor. I'm not sure what I exactly did that lead to this, but now my board ... (more)
I am using nrf52832 with PCA10036 V1.1.0. Soft device code is s132. I would like to know whether it will support Bluetooth 5.
I have downloaded nrf52 sdk13.0.0.04 version, in that PCA10036 folder was ... (more)
Following this tutorial : https://devzone.nordicsemi.com/tutori...
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
: *** [_build/nrf52840_xxaa.out] Error 2 make: *** [_build/nrf52840_xxaa.out] Error ...
I wonder is it possible to program nRF52 DK with Python instead C language? And are there any examples with python?
I'd like to create a firmware that supports multiple Nordic boards as Hardware (as the nRFConnect Firmware does). To do that I have to configure the peripherals according to the layout of these boards.
How can the firmware ... (more)
Are Nordic development boards compatible with Xplained Mini/Arduino UNO shield connectors sizes?
Can I use ARM DS-5 CS (http://ds.arm.com/ds-5-community-edit...) + JLink for nrf51822 development?
Thank you Richard
Hello, i think this is simple question, but nowhere i can find answer. Is nRF52840 preview development kit (PCA10056) contains built in nrf52840 microcontroller or i need to buy chip separately?
Thanks in advance, L3s
Hi, I'm new to development using nordic's products. Basically I'm a Hobbyist working on a project of mine, which needs a low cost wireless. I was looking for a Rf Soc and found nRF24LE1 which fits my ... (more)
I try to print the RSSI level but i couldn't do. I use nRF51 DK and soft device S130.
This is the line that i just write:
I don't need to connect the master with the peripherals, but i have to know how is the maximun quantity of scan response that can accept the master. In the example ble_app_multilink_central this is defined like that:
I want to program the BMD-300 with the nRF52 Preview Development Kit. I have connected:
BMD-300 -> nRF52-DK
SWDIO -> SH_SWDIO (pin #4) on P20
SWDCLK -> SH_SWDCLK (pin #5) on P20
VDD -> SH_VTG (pin #3) on P20
GND -> SH_GND_DETECT (pin ... (more)
I want to connect one board trough SPI to my nRF51-DK. Using SDK11 and SD130, the nRF51-DK is the SPI master, I call the function
nrf_drv_spi_transfer() but the CS Pin is never toggled. To solve this I changed it ... (more)
Hello, we have made cars that play laser tag against eachother using infrared emitters and receivers. The problem is that the infrared radiation bounces off the surroundings, and the cars end up getting hit by themselves.
The way it is ... (more)
I am facing a weird issue trying to achieve DFU over the air with the dual-blank DFU. I had integrated DFU with my application(Background story here.) The application hex file, app.hex was merged with s110 softdevice ... (more)
I want to program the ARM MCU in the nRF51822 Development Kit for my own purposes and then send the processed data using the BLE module in the kit to another nRF51822 Development Kit which receives the data and displays it.
I want to purchase a BLE development kit. My current preference is nRF51 because there are more nRF51422 BLE modules in the market. https://www.nordicsemi.com/Products/3...
I would like to run ble_app_uart on the BLE chip. Does ... (more)
I am looking for a nordic BLE development board that can do data transfer through the UART. Something like SPP (Serial Port profile). Here is what I need;
I am trying to use for the first time my nRF51822 development kit, following the "Development Kit User Guide v1.3". The problem is that when I open "nRFgo studio" I cannot see any Board on the "Device ... (more)
I get the following error when trying to build to target: make: * No rule to make target `nrf52832_xxaa'. Stop.
I am doing the following on the Blinky Example program: Makefile->Make Targets->Build->(Target) flash nrf52832_xxaa->Build
Please tell me the location to download the hardware files for pca10040 version of the nRF51 DK board. I could find only pca10028's hardware files in the nordic's webpage for DK.
I would like to know, can i use NRF52 Preview DK on Board Segger Section as standalone Segger JLink Programmer for NRF51?
So, is there any way to dis connect the on board NRF52? So, i can then ... (more)
I have 2 nRF51 Development kits and a nRF51 dongle that I am using for proof of concepts. I am mainly using the nRF51 IoT SDK because we are looking at using IPv6 with 6LoWPAN. I have a standard Bluetooth ... (more)
I just bought the Nordic Semi nRF51822 DK (without the starter kit). I tested the Heat rate monitor app and it worked fine. It could send some random values to the master control panel. I downloaded the nRF ... (more)
I have a new nRF52 Preview Development Kit, after connect it to a computer with a USB cable, the status light (LD5) come on, indicating it has power. However, the standard USB driver does not appear as described in the ... (more)
In IAR Embedded Workbench for ARM, version 126.96.36.19938 (w/ common components version 188.8.131.5284) with nRF5x MDK for IAR version 8.0.3.
When selecting the target in General options -> Target -> Device = nRF52832_xxAA, IAR cannot ... (more)
Where can I download the LED Button application example (explained in nAN-36) for Keil5 ?
Is there any compatible version with pca10001 board ?
I've found it here for Keil4.
Apart from this, in that Github repository you can ... (more)
Can you please provide full schematic for nRF52 dev board. I looked though the documentation and there are small bits of the schematic, but I didnt find full sch.