First time here? Check out the Tour!
Is it possible to programmatically assign a static mesh-local EID IPv6 address to a node in a network? I would like to communicate to individual nodes in the network using the EID addresses. I know the EID IPv6 ... (more)
We are using nordic thread sdk's sample simple coap client and server.We want to ON/OFF LED of coap client from coap server.
Can any one help how we can achieve this?
In the Thread API under the Command Line Interface section, there are the following functions:
void otCliConsoleInit(otInstance *aInstance, otCliConsoleOutputCallback aCallback, void *aContext) void otCliConsoleInputLine(char *aBuf, uint16_t aBufLength)
I'm assuming these functions can be used to manually ... (more)
I'm developing multiprotocol applications based on examples from Thread SDK: Proximity/CoAP server and BLE UART/CoAP client. All CoAP communication in this examples is initiated from client by sending requests, but I'd like to have a ... (more)
The SoftDevice uses the GPIO pin and port abstraction to configure and control IO's. When developing in Thread, how does one access and control the nRF52840 GPIO's using the Thread SDK?
I see no APP_TIMER_INIT macro in app_timer.h in Thread SDK. How should I use app_timer then?
I'm trying to add Openthread support to my project, which is based on ATT_MTU_Throughput example. I followed the tutorial in infocenter, but I still have some problems in linking stage:
Thanks from advance for your help.
Hi, I wrote an application based on ATT_MTU Throughput Example. Now I'd like to add support for Thread protocol. Is there a possibility for adding OpenThread libraries to Keil project? Here:
is only explained ... (more)
I was reading the Wiki page for porting OpenThread to a new hardware platform (https://github.com/openthread/openthr...) and I noticed there isn't a "flash.h" header file and a static library specifically for handling flash ... (more)
I'm trying to get the RSSI of incoming 802.15.4 packets using
otLinkRawGetRssi(), but I need only RSSI from one specific device. I tried to use whitelist (
otLinkSetWhitelistEnabled(), otLinkAddWhitelist()) and I checked in CLI that whitelist is ... (more)
I would like to know what the default value is for the radio TX power for the nRF5240. According to Nordic's specification, the output power is programmable from +8 dBm to -20 dBm. I see there is ... (more)
I wonder if someone can help me out. I would like to send serial data by modifying the 'simple_coap_server' main program. I added the following header 'app_uart.h' to make use of the functions but when I compile ... (more)
I'm currently setting up three nRF52840 DK nodes, two nodes are routers and one is an end-device. My plan is to introduce more node in the network later on. The IP address details of the nodes are ... (more)
At the moment, I have three nodes and would like to configure one node as an end-device and the other two as routers. Using CoAP, the simple_coap_server is used for the router nodes and the simple_coap_client is used ... (more)
I'm currently busy going through the OpenThread API and examples to better understand what all the functions do. However, I don't fully understand where the software is for the OpenThread stack and how it is burned ... (more)
While reviewing the Thread DFU examples I saw that Nordic ported the IoT CoAP library to thread. Is it possible to use other IoT libraries with some modification? Obviously only the UDP based ones will work.
If not, are there ... (more)
Hello! Based on you example I try to develop a simple HelloWorld example that follows chapter 11 of the specification. It says that to form a network a energy scan should be performed. That works perfectly fine but during role ... (more)
Hi, I currently try to build a little thread network with a border router bridging to ethernet. I did everything like in the Border Router Quick Start Guide and as far as I can say, everything works fine. My problem ... (more)
I'm looking into a project that needs to have BLE to communicate with a user and a mesh network to communicate with multiple data gathering nodes connected by 2.4GHz RF links (some nodes will be geographically too far ... (more)