First time here? Check out the Tour!
I am using examples\ble_central\ble_app_uart_c\pca10031\s120 in the SDK 10.00 .
I know that s120 supports up to 8 peripherals. I am using NRF51 Dongle as a Central. For now, I can only connect to 1 device ... (more)
We use the PCA00031 dongle running the MEFW 0.9.0 in our production environment to validate a sensors accuracy. The PCA is controlled by a C# test program using the Master Emulator and Iron Python DLLs. I've ... (more)
We use Nrf_studio to connect our board by uart to enter direct test mode. But an error occurs in serial connection.
I want to know， use our own project program is allowed ？ Or must program official dtm project can enter ... (more)
I am trying to find examples for nRF51 dongle P10031. I would appreciate some guidance and help regarding the same. Its my first time using the device.A link to a sample example or question would prove helpful too. Thank you
I am trying to run the examples given by Nordic on my nRF51 dongle. Most the examples are for PCA10028 or PCA10040 where as my dongle is PCA10031. I tried running them but i am not able to get the ... (more)
I have an after market breakout board for nrf51822 with a usb-to-serial chip (cp2102) that I bought from Amazon. It should act as an NRF51 USB dongle (pca10031-like) but with half the price.
I managed to flash the MEFW on ... (more)
By using ble-sniffer, I success to catch BLE Advertising packet with my NRF51 Dongle in CMD and WIRESHARK either.
But, I can't sniff any other packet except type of ADV_IND, ADV_SCAN_IND, SCAN_REQ.SCAN_RSP and some of Unknown (CRC Incorrect ... (more)
I am using nrf51 dongle on which I have loaded example code for BLE central(ble_hrs_c) from SDK 11.0.0 's example folder + soft device S130.
My problem is, I am able to connect with another dongle loaded ... (more)
Our BLE product uses a meander PCB antenna similar to PCA10031. It works actually quite fine, but a question pops up when it comes to tuning.
Antenna matching design in the PCA10031 module looks a bit strange.
I do not ... (more)
I need to do an hybrid app like nRF UART App but with cordova. i can connect and disconnect, but i don't know how to catch the data every time the ble send.
i'm using this plugin https ... (more)
Conditions in https://www.nordicsemi.com/eng/Nordic... have been met, ie all components of PCA10031 have installed successfully with the versions below:
Master Control Panel v22.214.171.12498 JLink CDC UART Port v6.0.2601.5 Portable Device ... (more)
I am having some issues figuring out how to send a simple string or character to my central.
What I want is the peripheral to send an acknowledgement back to the central that it is connected.
I am building on ... (more)
From bLE RF sniffer user guide:
To set up the Sniffer you will need one of the following pieces of hardware: • nRF51822 Evaluation Kit (PCA10001) and a mini USB cable • nRF51422 Evaluation Kit (PCA10003) v3.0.0 or later and ...
Is it possible to step debug PCA10031 MCP firmware using Keil?
I have a BLE thermometer I want to snif using nRF-Sniffer and Wireshark.
Unfortunately I'm unable to sniff the data, I only see the initial "hand-shake".
a) I start RF-Sniffer and then Wireshark
b) I initialize pairing ...(more)
Do the Nordic Boards offer some sort of config region where settings like the Bluetooth address are stored? I would like to change these settings without having to recompile.
If there is a separate setting for the Bluetooth address: Is ... (more)
I am attempting to get the ble_app_beacon example working with the s130 softdevice instead of the s110. I am using armgcc and the v8 sdk softdevice headers on a pca10031 dongle. I have the example working fine as it ... (more)
I've been looking for information on GCC support for the DFU bootloader examples in SDK v7.2.0 for the BLE Dongle board(PCA10031) but unfortunately there's nothing in the SDK. I've found a couple of GCC ... (more)